Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Can anyone tell all the potential reasons for stack corruption? I'm debuging a problem where sometimes there is no stack trace when putting a breakpoint on the first line...
I have a project based on SDK 15.3
I've set #define NRF_LOG_DEFERRED 1
The project generates a high volume of log output over RTT
NRF_LOG_FLOAT_MARKER is a macro that...
Hi, I am using the nRF51822 with SDK 12.3.0
I am trying to make use of nrf_drv_spis driver included in the SDK.
My purpose is to have nRF51822 constantly be RX-ing over...
While investigating my stack corruption issue , I noticed that the RADIO_IRQHandler is always called twice in quick succession:
But the NRF_RADIO->INTENSET register only...
I'm trying to communicate between two devices (nrf52840 and teensy 3.6) over RS485, but I'm having some issues using the UART library in the SDK. I'm trying to create an interrupt...
Hi,
It all happened today after being used the board for a month. when I tried to turn on the board it does not blink LED5 nor does it show up in the device manager. I to...
Hello Nordic,
I have multiple Thingy52 devices upgraded to V2.2 firmware via nRF Connect application on my android phone.
Have been trying to add the BL Mesh light switch...
I want to read timestamp in my nRF9160 device and found that "z_tsc_read()" function in Zephyr RTOS will do that. However, I am not able to include the main library of the...
Hi,
We are developing mesh control lighting system with nrf52832, now we're able to control devices through mesh.
But now we're having problem with showing node state...
Hello,
I have two devices, one central and one peripheral and I try to implement whitelist. I took a look at ble_app_hrs_c example and the whiltelist is working on central...
Hello,
I am using ble_app_blinky. I have a basic query about event handles. There are lot of event handlers registers as part of initialization. Will all these event handlers...
Hi all, we has experienced two PPK boards start to give faulty reading after several uses. I attached two screenshots about current reading with same setting on the DEV board...
Hi,
after having a little break from ot and working on another project, I am back working on getting the NRF into systemOFF. to get back into it I just made a very small...
Hello there,
Prior to updating to the latest modem firmware i was able to successfully get responses from the DK.
Running the Asset tracker app as well as AT Client. ...
Hi
I am currently trying to connect the sht31 temperature / humidity sensor. First, I made an implementation based on the twi_sensor example. I did it all, the temperature...
