Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I need to interface both, an SD card and a smaller (~4Mb) external flash to the nRF52840.
The SD card will be interfaced using SPI.
For the external flash...
I would like to store some parameters in nordic's non volatile memory and be able to restore them after power off.I am using the soft device s130.
I have checked both examples...
I have made a HDI 4-Layers PCB. I referenced the example PCB, but my board it do not work.
The softdevice is:s132_nrf52_6.0.0_softdevice.hex
The example code is: ble_app_uart...
Hi all,
I follow advice here " devzone.nordicsemi.com/.../nrf52832-ble-scan " to do the ble scan, I have question that there is a function to store scanned ble to the list...
Hello,
I generated the assets tracker sample project (like in this image below).
After building all the projects, I want to connect to jlink to download the project...
when i downloaded a git-hub ble-advertising tutorial and then tried to compile using segger. it gave me this error.. i am using nrf_sdk_5.2 and soft_device of S140.. i cant...
Hi,
I've got a suggestion to use for nRF52832 Multilink Universal FX or Cyclin FX programmers.
Even though the Segger programmer only suggested by Nordicsemi.
Can you...
Hi,
Last week I bought two NRF9160 DK. I downloaded the nrf connect on pc and then i followed the steps carefully from this webpage https://devzone.nordicsemi.com/nordic...
Hi,
I'm trying to send out 3 bytes just before I reset the chip. I am using nRF51, SD 130 1.0 and SDK v10.0.0. UART works well in other parts of code.
My original solution...
I'm using the nRF52832 +SDK11.0.0 +s132. I am making a making a library with floating point calculations and compiling it with GCC. A couple of test functions are:
I noticed...
Hi, noob question here I'm sure, haven't done any development in a while..
I'm trying to use the <windows.h> library for my program. I am using SES for my project. I added...
Hi,
I noticed that some of the GND_Shield pins on the nRF9160 (described in the product specification) are not connected on the nrf9160 DK. Why are they not connected to...
Hi ,I'm using nRF52832 Bluetooth DK and (SDK15.3.0) , I am trying to switch between beacon mode and uart mode without the need to reset button , e.g with reset button from...
Hi,
using a stock nRF52840 dongle and willing to enter bootloader (same as pushing the relevant button on the dongle) from app. How can that be done, using stock bootloader...
Hello,
I am using custom board with nRF52810 (QCAA, QFN32), SDK14.2, and softdevice S112 v5.1.0/S132 v 51.10 according to the compatability matrix. I am programing the board...