I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello everybody. Using the nRF52840-DK board and the Nordic example ble_app_uart_pca10056_s140 I am sending 200 bytes, repeatedly, to the Nordic UART APP. Everything works...
Hi,
What is the best approach to use a block of flash in nrf52840 as EEPROM. Are there any pre-existing library support for the same?
Also which is the best flash operation...
Hi,
I have gone through the lfs file system from zephyr samples but I could not find any solid documentation for fs and spi flash drivers available.
I have written the...
Hello,
I want to use the PWM driver to change the output voltage with respect to analog input voltage. If I call the simple_playback_sequence from the SAADC event handler...
Good day. Some smartphones cannot connect to NRF52832 (SDK17): - iPhone XR - iPhone 11 Detection goes well, but smartphones cannot fully connect and freeze at the connection...
Hi Sir,
We tried to download the nwp_024 , and check the tape reel information of nRF5340.
But we could not find the nRF5340 lists in "table 2. Carrier tape dimensions...
Hey everyone,
I firstly want to preface this with my lack of credentials. I'm very new to embedded systems development and am figuring things out slowly so please bear with...
I want to initialize LFCLK on startup to reduce power consumption. I am doing it as given below. Is this the correct approach of initializing LFCLK to reduce power consumption...
Hi,
I am using nRF52840 as BLE peripheral, on a Zephyr application under NCS 1.4.2
I want to limit the connection interval to 7.5ms (min+max)
I can see that the only...
Hi Nordic DevTeam,
I am using nRF52840 (1MB Flash, 256kB RAM). I would like to store a log data to flash memory that I can extract them to my Android phone later on when...
Hi All,
I want to verfiy the current consumption of nRF52840. I'm using an nRF52840 DK and SDK 17.0.2 RTC example. below are the verfiy steps:
1. Cut SB40 on PCA10056...
Hi,
I we are developing project on BLE NRF52832 module and it warked correctly. during the debugging suddnely it stoped responging to programmer and couldn't be reprogrammed...
I have read about eddystone protocol. I have run
nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_eddystone\pca10040\s132\arm5_no_packs
i am able to build the code...
