I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello, when trying to finish provisioning my nodes (3 total, per example program's instructions), my provisioner program keeps running into
NRF_MESH_EVT_PROV_LINK_CLOSED...
i am using three boards , one is client (nrf52840) and other two boards as server(nRF52832) using light switch example . i want to get the message from client board ,to relay...
Hello,
I am having trouble understanding how the following function in the PWM driver example under peripherals in the SDK. Below is demo1 from the code that creates and...
I am not able to enter DFU Mode with secure bootloader example.
I use IAR and NRF Connect with Programmer to flash
Following are the steps I followed
1. Build Secure...
Hi Everyone,
In this code I'm face a problem. The issue is when i debug, it shows "<info> app: TWI device detected at address 0x6D" . Please find attached a snapshot of...
Hello,
I scrolled through some subjects about that SoC already but I wanted to get some more precision.
1. Can I start developing solutions for AoA / AoD system...
I am trying to do a ramping PWM. I want to update PWM every 25ms by increasing the duty cycle by 10%. I tried to setup a timer, by calling app_start_timer() on repeat mod...
Can you clarify how FLASH_SIZE, defined within the linker_section_placement_macros setting in the Segger Embedded Studio project file is used? Specifically: should it reflect...
In the light switch example, I try to change the network-key and then get some new unprovisioned servers provisioned.
The servers seem to get provisioned, but the client...
Hi,
I am working on NRF52840 preview DK using SDK version 15.3
I have compiled and loaded the Secure DFU bootloader onto the device, and also successfully got the BLE_BUTTONLESS_DFU...
I am using the mesh SDK version 2.2 (I think - I renamed the folder when I started, but I can't find a reference to the version number in the library! I am sure it is 2-point...
Hi,
How to calculate the free Ram and Flash after I loaded bootloader + SD + App on a running nRF52840?
I want to know ways to measure during critical RAM load too.
...
Hi, what is the correct way to erase all the connection params of a zigbee router device (not coordinator), and restart to search for a network automatically in production...
Hello,
I am using SDK 15.2.0 ,nrf52840. In my application we are using bluetooth and USB. The application works good. The device advertise and can get into the application...
