Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
HI,ALL
Is the scanning device always get the BLE_GAP_EVT_ADV_REPORT Event ?
my current project is
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_central\ble_app_uart_c...
Hi,
I'm using SD110, SDK 10.0.0, nRF51822
In my own application, I control 4 servo by pwm with Timer1 and Timer2,
and I have 2 buttons, each button is a flag for...
Hi now i"m working on nrf15882 ,i'm confused how to test ble_uart example?
when i connect to the device(nrf15822),the cellphone app always displays:connecting,
later...
I'm trying to get a hold of a few nrf905 dev boards. Most the ebay boards have "nrf905 (ptr8000+)". Is there any difference between these chips?
I'm assuming the ptr8000...
Hi,
I setup the nrf51 as in central mode and talking to an ARM Cortex mcu via spi bus with the NRF51 set to slave. The spi communication working fine, but when I star scanning...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_hrs_c" "ble_app_uart_c" as reference.
My peripheral's Service UUID = 000098000000100080000017FFE07A00.
I want to...
Hi,
We intend to use nRF5x as main uC for our upcoming 4 new design. (diff. kind of measurement devices)
Instead of qualifiying each new device, we have intended to...
Is there a list somewhere that correlates the NRF_FICR->CONFIGID value with the actual nRF51 variant?
I had orginally used the 16K Ram versions, but when Nordic release...
Hello,
I'm implementing long write function to my project.
I managed to get it working, but i can't send more than 68 bytes of data.
When i'm sending the data, I slice...
Is there a way to tell if the timer is running? There's a start task, and a stop task, but I'm not sure how to tell if a timer is currently running. The best thing I can think...
Hi!
I developed my application using nRF51 DK with nRF51422 QFACA10 chip on it, and everything works fine. But now i would like to program this application on nRF51822...
Hello,
sd_softdevice_enable never returns.
I have no 32.768 KHz crystal but is set lfclk with NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM.
I'm running my application on a custom...
hi,
I am using currently keil v5. and sdk5.2, softdevice s110 v6.2 for board PCA10028 by changing header file of broad nrf6310. And also when i have been compile dfu_dual_bank_ble_boot...
I would like to confirm the number of available and configurable PPI channels for the application code when Softdevice S132 is used. I am using nRF52832.
In the Product...
