Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Environment : - nRF Connect SDK v3.4.0. - CONFIG_SPI_NRFX_SPIM_RTIO=y. - SPI_HOLD_ON_CS is not enabled. The same completion ordering is present in upstream Zephyr main : https...
SDK: nRF Connect SDK v3.4.0 (LTS) Library: nrf/lib/sms
Summary
sms_register_listener() is documented to return a listener handle or a negative error code. In practice...
Hi,
Initially, I can send and receive AT commands. But after sending the power-down commands
sequence from "Getting Started with nRF93M1 DK v0.4"
I could not receive...
Hi all,
Quick question on NFC design practice.
I am using the nRF54L15 NFC in tag emulator mode (differential), with the following setup:
Antenna: Molex 1462360051...
What high-temperature storage (JESD22-A103) and temperature-cycling conditions was the nRF9151 qualified to (temperature, duration, cycles)? Your DevZone forum mentions 125...
Hello,
Thank you for your help.my questions are as follows
SDK : ncs 3.4.0
Hardware board ：nRF54L15
Based on the ncs SDK 3.4.0, how should one set the MAC address...
As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi Nordic Team,
Does the reset of 54L15 need to be handled? Still pull up a 1k resistor. Also, do I need two wires for debugging?
The customer has another question....
When transitioning from ncs v3.3.0 to ncs v3.4.1 noticed a warning about CONFIG_BOOT_ECDSA_CC310 being depreciated when building MCUboot. The release notes suggest using PSA...
I am using display example code from zephry repo. ( zephyr/samples/drivers/display at main · zephyrproject-rtos/zephyr ) . Connected to a nRF7002 dk , i am using EA W096016...
Hi,
We have a custom nRF5340 board with an nPM1300-QEAA-R7 (QFN32). On two assembled boards the PMIC behaves identically:
Power side works: it ACKs at 0x6B and the BUCKs...
We are currently working with a system that is using both and external flash and the HW WDG from the NRF5340.
Recently we are facing the issue, that we cannot re-flash the...
Hi Nordic Support,
We are using an nRF54LM20 DK, PCA10184 hardware revision 0.7.0, for automated side-channel analysis (SCA) testing.
Our requirement is to repeatedly...
Hi,
We are having issues with getting the output power of +23dBm when using the nRF9160 DK in CW mode.
We use the following command:
AT%XRFTEST=1,1,20,8470,23,1,4,0...
