Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hi
I am going through the AWS IoT example using an nRF9160 DK, but having some problems with it.
My setup
nRF9160 DK + LTE-M SIM card
I used this same board and...
Hi,
We are working on adding T-M to our middleware, and we discovered a pretty annoying side effect.
We are using NCS 2.0.0
One of our device is controlled using the...
Hi
According to Case ID: 279868 it seems like there has been some issues with modem lock up on nRF9160.
Some questions:
Do you know if this issue is still valid...
Hi there,
I am developing a central in nrf52840 dk using SDK v2.0.0 in VS code.
The BLE part is OK and it is possible me to get notifications.
Now, I need to store the...
Hi,
I have nrf52840-Dongle and nrf52833DK and it was working all good few days back with my code for BLE-UART (Centeral-nrf52840 Dongle and peripheral nrf52833DK) but now...
I need a crystal capacitor for this two Crystal XRCGB32M000F1H01R0 and SC20S-12.5PF20PPM. The value of this capacitor is 12pf and package 0402 So, please help for selection...
I am using a rotary encoder with nrf52840dk and I am confused about how to run sample QDEC code from zephyr/sample/sensor/qdec on nrf52840dk.
I got this error when i tried...
Hi Nordic Team,
Thank you for your support.
One of our customers got Version 2.1.0 for two.
But it was confused. Box label is 2.1.0. But board was 2.0.0 and both...
Hi there,
I have an smart product that will use both BLE & 2.4G Radio. There are few question about framework.
1. I saw radio packet contains such as S0 S1 ADDRESS etc...
I have noticed that the function sd_rpc_open(...) of pc-ble-driver takes more than 1.5 seconds.
I have tried an example heart_rate_monitor which is supplied with pc-ble...
Hello,
I am using nRF52840 DK, and SDK version 17.1.0.
I want to dynamically control CLOCK source.
I tried to release( STOP ) HFCLK( XTAL ) source using nrf_drv_clock_hfclk_release...
Hi there
When the EVENTS_DEVMATCH is raised, this signals that the device address received in the radio data packet matches one of all enabled addresses in the BASE0/BASE1...
Hello,
we faced sometimes the issue that the reset reason Register RESETREAS is Zero at Startup. What does it tell me? So what happend in the Firmware that there is a reset...
I haven't been able to find any documentation or forum posts along the lines of the problem I'm having, so...
I'm trying to use an nRF52-DK with nRF Connect Desktop to connect...
