Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I'm running some power tests on the nRF52 DK and, after fiddling with some of the power settings, I'm managing to get an idle current of about 1.8uA on the coin cell, and...
I'm sorry to ask a question that I'm sure has been answered before, but I can't find another post similar enough to be of help. I have an HID application that bounces back...
Dear All,
We are currently developing a low power application for the nRF9160, with ncs zephyr version 1.2.0. For our application we want to trigger an interrupt on both...
I Upgraded the software to V3.6.1. The button "Start DFU" is missing from the SFU mode screen. After choosing a Zip file there's nowhere to continue. Had to downgrade the...
Hello,
I'm developing an application using zephyr, openthread, udp, and nfc, targeting the nrf52840 (currently developing on nrf52840dk pca10056).
I initially developed...
Hi,
I would like to get some information about the reset's reason of my nrf9160 like
- The reason is due of an assert type "xxx"
- Where is the stack pointer
- .....
Hello,
I'm developing a BLE device and it consist of nRF52833 and a external UART component.
ble_app_uart example in SDK v17.0.0 is replaced app_uart to libuarte. The...
Hi,
I would like to know if we can enable codded phy while using mutli peripheral in conjunction with mutli central. Also peripheral should be scannable and connectable...
When creating dfu package using nrfutil, an error is displayed.
When I looked for and checked the file where the error occurred, a problem occurred in Python's max...
I am trying to run nrf52840 chip without debugger.
I want to run peripheral_uart example just to show advertising of bluetooth.
And when I use west debug --runner=jlink...
Hi,
I got a nordic thingy:91 and just play a bit with it and the asset_tracker application. Then I flashed the agps code because just want to send GPS coordinates on the...
I am having issues using port pin 1.00 on the 52840 as GPIO. It will just not toggle.
I can successfully use most other pins, even those on the higher port. For example...
Hi
I have 2 identical PCB just out of production - same FW - one is drawing higher current (about 600uA).
The issue is found in mass production and about 1% is having...
I'm using nRF52 DK to send SAADC data to mobile app "nRF Connect" over BLE.
I'm using this code to send the data, but the mobile app "nRF Connect" can only show integer...
Hello Devs.
I am porting my whole project from the SDK16 to NCS 1.4.1 on my original project I use I2c and other drivers which works pretty well, but I am able to make them...
