Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hello,
I am attempting to find gerber data for the development PC or a mechanical drawing of connector locations. I would like to make a PCB that plugs into this board...
Hi, guys! I noticed this answer from the devzone .
I have nRF52 DK and an nRF Thingy. I want to play a short speech using I2S with MAX98357A .
This speech is usually...
Hey,
simple question: What is the recommend approach on prolonging the advertising period?
Example:
User clicks a button -> advertising starts for 180 seconds.
User...
Hi Support,
I am testing current consumption of NRF_TIMER1, below is my code snippets, basically, I just start timer1 task and then stop it.
After the two code lines...
Hi there, I really much in trouble with USB CDC ACM. So that would be great if you can help me out with this: I upload the "USB CDC ACM" example (SDK verison 15.2) to my nRF52840...
This is a question of curiosity rather than a specific concern: In my sdk_config.h I have my prescaller set to 0: Based on this, the RTC1 used for AppTimer should rollover...
I am working on an older project that was developed using SDK 11.0.0, SD S132 2.0.1, and "Eclipse 2018-9." No MDK appears to be being used.
I understand that the MDKs are...
Hello,
BLE 5 applications on the nRF52810 which softdevice should we be using S112 / S132 what are the primary differences between these? I wanted to know a comparison...
Hi,
I'm collecting data from BLE and storing them into nRF52840 Dongle by using nrf_fstorage_write procedure. Everything works fine so I can write data into flash by nrf_fstorage_write...
When I run the TWI scanner example, an unknown address shows up in tandem with my TWI device address.
I am connecting a MAX30101 EV kit daughter board to the nRF52840...
In the secure DFU bootloader, I have some custom initialization that I need to happen after the BLE transport is initialized in nrf_dfu_init(), but before loop_forever() in...
Hello everyone,
I've got an issue with ESB. I'm using 3 nRFs 52840 with firmware based on SDK 15.2. One of them, the radio-receiver is RX, and two of them, PilotA and...
Hi,
I'm working on putting our system into low power idle mode. We use MyNewt to build our application. In order to get to the lowest power, I disabled BLE and all our drivers...
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
