I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi All,
I have a basic question, i want to know what are the right value to use with the nrf51422 chip for the resistors with ADC.
I want to use the maximum value permitted...
Hi, I have problem with using example codes. I want to add GPIO control to ble_app_uart example. Adding gpio_config() function taken from app_timer_tutorial blocks program...
I'm using NRF52832 SoC and IAR
I've to read data from ADC using SPI. ADC will generate interrupt every 4ms indicating data ready. I've configured GPIOTE to sense the ADC...
A couple of power consumptions Q's for this basic scenario: RTC used via PPI to infrequently sample from ADC and trigger SPI read from external sensor source.
Questions...
Hello,
I need a support for BMD-300 BLE module.
We can flash the BLE module and we can connect it with mobile application via Blue-Tooth.
But when we flash BLE for...
Hi,
I'm using nRF51822 in my senior project (some kind of BLE wearable device).
I'm trying to call my function inside the ble_evt_dispatch() function but it doesn't...
SPI Slave configuration On nRF52
Hi,
I am trying to configure the SPI slave peripheral for interrupt based communicaton with a SPI master
In previous work with ARM...
Hi,
Can any one tell me about all the security features provided by nrf51822 s110 for secure communication?
Share me some example that implement encryption durring communication...
I have a problem with bonding with a static passkey. I have some sensors, which have a static passkey hardcoded in them. If I want to bond with them, I have to provide this...
Hi, I'm new with BLE applications and I'm designing a wearable.
This wearable will be powered with a CR2032 coin cell battery and I'm wondering if you recommend to use some...
Hello
I have a problem with the power of my modules nRF24L01
while awaiting the arrival of data consumption varies between 15mA and 20mA , I am feeding with 9V batteries...
Hi!
I'm using the RNG to encrypt data that I must send via SPI to another module. I'm using the function "sd_rand_application_vector_get", because I'm working with Soft...
Hello,
I'm just getting started with my nRF52832 and I am still trying to get the first example of the tutorial page running ( Getting started with nRF5 DK .
I did everything...
Hello,
I am doing a project that involves getting data from 2 PTX nodes from the slaves via ESB and sending the data obtained to my android phone via BLE. I am doing so by...
