pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello, I have stumbled upon a case exposing a bug in your lib/date_time/date_time_core.c.
In my case the modem re-registered and got a time from the network (%XTIME) right...
Environment : - nRF Connect SDK v3.4.0. - CONFIG_SPI_NRFX_SPIM_RTIO=y. - SPI_HOLD_ON_CS is not enabled. The same completion ordering is present in upstream Zephyr main : https...
SDK: nRF Connect SDK v3.4.0 (LTS) Library: nrf/lib/sms
Summary
sms_register_listener() is documented to return a listener handle or a negative error code. In practice...
Hi,
Initially, I can send and receive AT commands. But after sending the power-down commands
sequence from "Getting Started with nRF93M1 DK v0.4"
I could not receive...
Hi all,
Quick question on NFC design practice.
I am using the nRF54L15 NFC in tag emulator mode (differential), with the following setup:
Antenna: Molex 1462360051...
What high-temperature storage (JESD22-A103) and temperature-cycling conditions was the nRF9151 qualified to (temperature, duration, cycles)? Your DevZone forum mentions 125...
Hello,
Thank you for your help.my questions are as follows
SDK : ncs 3.4.0
Hardware board ：nRF54L15
Based on the ncs SDK 3.4.0, how should one set the MAC address...
As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi Nordic Team,
Does the reset of 54L15 need to be handled? Still pull up a 1k resistor. Also, do I need two wires for debugging?
The customer has another question....
When transitioning from ncs v3.3.0 to ncs v3.4.1 noticed a warning about CONFIG_BOOT_ECDSA_CC310 being depreciated when building MCUboot. The release notes suggest using PSA...
I am using display example code from zephry repo. ( zephyr/samples/drivers/display at main · zephyrproject-rtos/zephyr ) . Connected to a nRF7002 dk , i am using EA W096016...
Hi,
We have a custom nRF5340 board with an nPM1300-QEAA-R7 (QFN32). On two assembled boards the PMIC behaves identically:
Power side works: it ACKs at 0x6B and the BUCKs...
We are currently working with a system that is using both and external flash and the HW WDG from the NRF5340.
Recently we are facing the issue, that we cannot re-flash the...
