Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
I am new to nRF SDK. I am starting development for my nrf52810 based board. I am using blinky example from nRF5 SDK. I am using nRF52 DK board to flash and debug my nRF52810...
In our setup we are sending one CoAP message every hour. The transmission is set to be done at hh:00. Downstream communication is only required as a response to the upstream...
Hi, My name is Philex Fan who is a researcher working in academia. I am working with a group of researcher to develop biomedical device that can get brainwave signals and...
Hi!
This tutorial is just for current > Measuring current . I want the same for latency with code.
I'm working with two nrf5340 for Bluetooth low energy and I want to...
Dear Community,
From a provisioner, I want to get the MAC address of a device (provisionee) during the provisioning process. Is there an example somewhere in the forum please...
Hello,
I am using nrf52805 processor, nrf sdk v16.0.0 and Segger embedded studio. My board communicates with a temperature sensor over I2C. The software is working without...
Hi all,
I am working on a ble5 beacon with ecdsa signature. I would like to use mobile to verify my message. As I see that the crypto ecdsa example use raw key and generate...
I have developed an APP using SDK 15 (both BL and APP) updating Bootloader and APP which is working fine.
I have developed same app using SDK 17.0.2 (both BL and APP)
...
Hi, I know this topic has been up in several posts before, usually ends with, buy a LitePoint or Anritsu.
Assuming you want to do a poor mans measurement setup, just relying...
Hello, I've been trying to get the nrfx_i2s driver working with Zephyr, on the cpuapp core of the nRF5340. After configuring the driver, setting CONFIG_NRFX_I2S in prj.conf...
I've been successfully creating custom services, but there is one case where a device has a service UUID and it's 2 characteristics have completely different UUIDs (all 128...
Hi,
How do I set ncs v1.5 to save the last open project path?
ncs v1.3 has the last open road
ncs v1.5 does not have a project path that was last opened
Here's the...
Hello, I have a question. In the HID_keyboard routine, I have already bound two phones.
Now I want to cancel the binding, and the function was called by key interrupt pm_peers_delete...
Hi,
I am new to the zigbee development and currently going through the documents.
My end goal is to develop a application that measures the level of a tank using radar...
Hi
We are using an external 32MHz crystal to generate the internal 64MHz clock.
As described in several examples, we start the HFCLK with
NRF_CLOCK->TASKS_HFCLKSTART...
