Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello,
I'm very new with the DFU on nordic and I would like to know if it is possible to upload a valid application so that my DFY can jump onto it ?
Thank you in advance...
Hello,
I'm very new with nordic environment. i would like to modify the FDS address because it seems it is always put to the end of the flash and when i flash a new bootloader...
Hello,
I'm flashing a bootloader (DFU) and then i'm flashing my application but each time i flash the application, Segger Embedded reflashes the softdevice and the MBR....
When building the sample code using the latest SDK I do not see the device in the device manager and after a while I get this error:
Any hints on what is wrong ?
...
I have already made a post for this problem. Initially, Amanada Hshei gave some troubleshooting techniques and it did not work out,
Here is the original post, and My request...
Using Windows 10
Master Branch
Compiled using Segger 4.16
Downloaded merged.hex
When running NRF Connect Link monitor and connected to nrf9160
I receive the following...
HI,all
I have tested ZC and ZED to establish network,I found a method zigbee_erase_persistent_storage(bool),when i put true on ZC and put false on ZED, first time they can...
HI,all
I am a newman for zigbee on NRF52840 with S140 softdevice,
I have two board, one is ZC and another is ZED.
On ZC board, I use ZB_GET_OUT_BUF_DELAYED2 to send...
I am using sdk15.2.0 with PCA10040 dev board.
In ble_app_eddystone example, the configured advertising interval and duration dont match the observed values.
I think I...
Hi Nordic,
I have recently received an error from pm_init that I have never seen before, NRF_ERROR_INTERNAL. After some debugging, I found it was really due to NRF_ERROR_STORAGE_FULL...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi Team,
I transplant the project Uart from example/peripheral/uart tranplant to blecentral/multilink project, but it does not work, it indicate that APP_UART_COMMUNICATION_ERROR...
Hello,
In below link, I am bit confused between “With bootloader” and “Without bootloader”. What for this bootloader.
https://infocenter.nordicsemi.com/index.jsp?topic...
Hi all,
I purchase a Li-Po batter where it will output 4.2V when I connected to nrf52480 DK, it causes all 4 LEDs (LED1, LED2, LED3, LED4) not functioning anymore.
The...
