Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I can see a phrase "Not recommended " on the Evaluation Kit's page: www.nordicsemi.com/.../nRF51822-Evaluation-Kit
What could that mean for me if I already have the kit...
I found in ble_app_uart example, any device with UART app can connect to uart service and send something to COM port or just block the connection of other devices.
So can...
I'm trying to update my firmware using the dfu, I tested two examples of the SDK :
one of them is dfu_dual_bank_ble project,
I noticed that the memory allocation...
Hello,
I have been reading a lot of Nordic and DevZone stuff. The information I need appears to (almost) be there but I cannot quite put it all together. I need some help...
Hello, I am asking for your help again.
I just managed to brick the chip that I am working with. The problem is that I am not able to erase or program the flash. However...
Hello,
I have not found a lot of information on connection encryption. I want to use a preprogrammed Long Term Key in my mesh that is then used to establish subsequent...
This is the application file I am trying to download:
dx02.zip
This is the sniffer Log I just captured by wireshark
dx02_20150820.pcapng
I was able to upgrade firmware...
We have a heavy duty scan based application being built on top of the nRF51822 SOC. We have tested the scan function (S130 SD) on both a custom PCB and also the Nordic Smart...
Hi,
I have PCA10028 board, and I'm trying to implement UART send/receive.
I've searched for the problem here but could not find a solution for it.
My uart init function...
Hi
I'm using Keil V5 to program the Nordic nRF51 DK ( the one here: www.nordicsemi.com/.../nRF51-DK) but I'm a bit confused as to whether or not I need to change the settings...
I am not quite certain what the advantages/disadvantages are of using LDV vs DCDC if you are using an external regulator. In my case i use a LiPo battery outputting ~4.2V...
In the ant-to-ble bridge example in the 7.x.x SDK, there is the following comment in examples/multiprotocol/experimental_ble_ant_app_hrm/main.c :
// Need to close the ANT...
Hi all,
As I know in constant latency mode, both the regulators (1v7 & 1v2) and HFCLK are kept on. Is there a way to keep the HFCLK on while one or both the regulators...
Follow up this image. I want to reduce the negotiation time.
10:44:43.655 --> Connected to D6:9E...
10:44:45.123 --> Services Discovered
= 45.123 - 43.655 = 1.468...
