GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi All,
I am using asset_tracker example V1.8.0, it's working fine with nrf9160DK. I am able to see the data on nrf cloud.
The purpose of testing this board was to debug...
I am working on two devices, a peripheral and a central. The peripheral is custom hardware. The central is being run on a Rigado BMD-300 series evaluation kit. I'm using Segger...
Hi,
Perhaps this question is too basic, but I haven't been able to find this anywhere.
I've followed this tutorial successfully with an nRF52832 DK:
However, I'm missing...
Hello,
I wanted to create an SPI shell, similar to what is available for I²C. I am therefore trying to create a generic SPI device in the devicetree:
Somehow I am...
Hello,
We use nRF52840(0dBm)+nRF21540(Dec6).
In the case of using nRF52840+nRF21540, tx spurious emissions occurs severely in the nRF21540 output.
FEM(nRF21540) output...
Hi.
I am developing a custom board using the NRF52840. The mcu needs to connect to a modem and a gnss module. Both modules will communicate with the mcu over UART
I'm...
I'm working on a prototype that has 8 BLE sensor nodes that are powered by coin cells and placed on different parts of a human body.
The host node is the main processing...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
I have one central and one peripheral device connected over BLE. The peripheral has a custom service characteristic containing the firmware Version value. After connecting...
On a custom board we are using an RTC chip to generate the 32khz clock.
I have verified that the hardware register is set to external, bypass, and the src is xtal. The clock...
when i got a nRF5340 DK,
firstly,i use the vscode to open sdk and build ,
secondly,start to run the ncs2.1.2 sample (path:v2.1.2\nrf\samples\bluetooth\peripheral_uart...
I wan't enable approtect by add this line in main.c:
const uint32_t approtect_set __attribute__((used,at(0x10001208))) = 0xFFFFFF00;
but when i compiled at IAR,its show...
Hi, I'm setting up my environment on a new laptop. The project I'm working on requires tflite-micro and before I found that I needed to add tflite-micro to the 'name-allow...
Hai Team,
I am working on NRF52840 based on the BLE Connection handle
Here I am using the ble_app_multilink_central example of SDK
case BLE_GAP_EVT_ADV_REPORT: { uint32_t...
Hello,
I'm following this tutorial to learn how to create a Matter application from template. I did all steps and wanted to build the application. However, the build failed...
