Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
I'm trying to develop a Zigbee application, and following the guide provided here for adding a ZCL cluster to the Zigbee template. However, I think this guide is not...
Set up: Rpi Bluez 5.72 (provisioner)
nRF DK (light example)
steps:
1) trigger scan un provisioned devices from Rpi
2) able to see nRF device in scan results
3) start...
Hello,
currently I'm migrating a project from connect SDK 2.6.0 to 2.9.0. After some changes according to the migration guides the project builds fine and also runs.
As...
I would like to use nRF52832 DK to test Nordic UART Service (NUS). But west build failed with the following messages. What is meaning of "zephyr_pre0.elf section `noinit'...
Hello,
I am attempting to use the nRF7002EK shield with my nRF54L15PDK development kit.
I have custom code, but it's based on the wifi scan example provided by Nordic...
Hello,
I would like to know if there is a way that I could see the source code of the nRF Mesh Sniffer app for Android, just like the nRF mesh source code is available in...
Hi, I am currently using the nRF52832 MCU and have implemented hard fault handling as follows: I use the macro APP_ERROR_CHECK(err_code), which, in case of an error, calls...
Hi
I am trying to perform a full modem update on my nrf9160 DK board.
I started at v1.3.4 and successfully used the partial update method to go to 1.3.5
I then used...
Hi everybody, I'm looking to build a PWM generator with 2 outputs from 1-100Hz. Unfurtunately the current PWM API examples with Zephyr works only for 4-100Hz.
I've tried...
Hi,
I have just bought a PPK2 and (mistakenly on my part) assumed it must read the Voltage of the output as well (necessary for power measurements). I see now that it doesn...
I am using ncs sdk, my projects are under ~/zephyr-workspace. This is from an example project - blinkypwm. The clangd compiler shows the following erro: In included file:...
I try to simultaneous update (app + networkcore) with usb and external flash on my custombord And serial recovery, not DFU from app.
this is mcuboot config. I have set the...
i want to commission matter compatible smart switch into thread network.
but i'm getting internal error .
but other device like matter samples light_bulb (nrf52840dk)...
