Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
hello,
i am working on nrf52 dk board .NUS sdk 16
I'd like to know the start/end characteristic handle values for each service. Is the 32-bit service handle encoded as...
I have inserted the groups cluster at an endpoint. Yet, and eventhough a group seems to be additioned to the device (the device responds with 0 to the add group command from...
hi:
I need help with a problem.
Error in merge file for 52810.
use sdk:nRF5_SDK_17.0.2_d674dde
bootloader:secure_bootloader
app:ble_app_buttonless_dfu
app:FLASH_START...
Dear Nodic friends,
We use nrf52833 to design a BLE control box with USB DFU function.
During USB DFU, DFU Trigger Library will reset nrf52833, so we should connect a...
Hi
I'm trying the light lightness example, I'm using nRF Mesh Android app for provisioning. I've 2 nrf52840 DK's. One is for client and other one for server. Both of them...
Hi,
I am trying to implement BLE on nRF52840 using Zephyr APIs. I am wondering if anyone can elaborate how to use bt_gatt_write() and bt_gatt_read(). As of now, I am able...
Hi:
s132_nrf52_7.2.0_release-notes.pdf shows us below words in page 3 about limitation:
GATT:To conform to the Bluetooth Core Specification v 5.2, there shall be no secondary...
I am creating a system with one BLE central device (nRF52840 DK) and many peripherals (nRF52840 Dongles). I am attempting to create a BLE central device that interfaces with...
Hello i have a working program with ble:uart and twi in a nrf51822 device with sdk 12.3 and softdevice My system works perfectly when i use other gpio as scl and sda (external...
When I'm tuning the RF output (front end) of the nRF52832 to match 50 Ohm what state should the chip be in? Unprogrammed with power on or off? Or in receive mode with power...
Should a firmware written for nRF 52832 run smoothly on a nRF52833 if no changes in functionality are desired?
If changes to the firmware are needed, which layers must be...
Hello , Vivek here. I am planning to use NRF52832 in my design and interface it with a microcontroller. And i am new to handling bluetooth protocol. When I was going through...
Hi,
i am using nRF52840 SoC and Had confusion on pin mapping for SPI (external flash) and I2C (external sensors) as below:
I found one similar query and it was said...
Hi,
I would like to write a code where I send a packet from a nRF5340 DK to another nRF5340 DK by using Zigbee.
I would like to also be able to use printk and see the...
Hello Development team!
First off, many thanks for all the help provided so far.
I'm trying to add the ZCL messaging cluster to the multi sensor example, how could I go...
