Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hello,
I have a device that advertises as `BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED`. When a device connects, it restarts its advertising as `BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hi,
i have developed a Windows based App in Qt that using BLE.
My problem is upgrading a remote device Firmware using BLE.
Did exists any type of C++ class automator...
Hi Nordic!
I faced a problem when I want wake the MCU up from SystemOFF.
When my nRF51822 is in SystemOFF mode, a watchdog chip wakes up the MCU. After sending the...
Hi.
I think i just fried my NRF52840 dongle. VDD out is only about 0.5V :| I'm currently powering it from the usb port (VBUS is correctly +5v). Could it be that Ii only...
Hi,
I"ve designed a custom board with the MDBT50Q module (part of the schematic below). When writing my program to Flash 0 and Ram Memory 2000 0000, the program won't load...
I have been experimenting with the example of the MQTT Client Subscriber/Publisher from de nRF SDK. I use:
SDK v15.3.0 (also nRF5 SDK v15.2.0).
Raspberry Pi 3 (as a...
Are there any working projects that integrate TWI and MPU6050 sensor. That are edited by KIELu5 and follow the SDK 15.3v ? I tried modifying the 'twi_sensor' project but I...
Good day
Im trying to switch off an LED when my relay/hopper is not advertising. I switch the LED on successfully when transmission starts but I'm struggling to do the sd_ble_gap_adv_stop...
Hi, everyone,
now I'm test " \ncs\nrf\samples\nrf9160\gps\build_nrf9160_pca10090 ",
it's error about" nrf_socket.h: No such file or directory"
I'm find the file at ...
So this is a small continuation of this ticket https://devzone.nordicsemi.com/f/nordic-q-a/50656/using-pdm-mic-on-nrf9160dk .
The problem I'm having now is that when I run...
I wrote UART echo sample based on ble_app_uart_c for S140/ nRF52840-DK.
When nRF52 receive one line on USB/UART, it send same line to USB/UART.
I also write Linux socket...
I am following this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/application-timer-tutorial?CommentId=43347679-22d9...
Hello,
I want to use the ADC for a burst @ 8khz.
I use this sample " test_adc_sample_with_interval " from https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
Greetings...
Please help me understand why PB-GATT support is removed from SDK UART coexistence example?
The dilemma I am facing is as follows:
1. No PB-GATT for SDK...
