Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I have Wireshark setup with old PCA10028 board connected as a sniffer, FW sniffer_pca10028_51296aa.hex Now I'm working with NRF52 family and sometimes I need to observe some...
Hello everyone ,
i want one central uart and three uart peripheral , i want to connect the central to all three peripheral , if i send data from central , it should receive...
Hi
I have a problem with showing data packets in wireshark. I configured the sniffer according to the instructions. At capturing packets in main window don't show anything...
I want to use UART.
I checked the waveform and UART does not send data. Here is my code. build and run are successful. Any help? I connect UART RX and TX directly, which...
hi... how to make a nordic app to act as a peripheral , i have read one post , in that they mentioned set up to be done in gap peripheral mode . how to do that
IAR 7.60
52840
nRF5_SDK_15.2.0_9412b96
Hi there, I'm trying to do some modification in the bootloader (so that we can write the image to the flash's bank1 using our...
Hello,
I read through the Bluetooth core specification in order to get a better understanding of the information that has to be stored at a minimum if using bonding. But...
Hello,
i'm trying to use ble_advertising_init to initialize my advertising data, but when i use this function like it is used in the examples i get NRF_ERROR_INVALID_PARAM...
When I open device just after I plug it in the PC it work fine, but when I try to do it again (exit python script and run it again) I'm getting Error code 13.
Firmware:...
We are currently in the prototype stage using the nRF9160 and are preparing the firmware for the prototype. We have a few question that we hope someone could answer :)
Will...
Hi,
I want to test BLE 5.0 using two nRF52 dev kit. i am using the ble_app_uart example kindly guide me what are the changes to made in this example to connect two kits...
It's easy for me to create make file target but I am not able to identify where and how to add the custom target in the Segger Embedded Studio(SES).
My default build configuration...
Hi everyone. I am trying to find the best way to establish a Bluetooth connection to a nRF52832 in the least amount of time.
I'm designing an ultra low power perpheral...
Hello,
Would it be possible to create a partial code that can be placed on external memory, and loaded into ram for execution when needed?
As I believe it is possible...
Hi,
I am developing a Bluetooth peripheral application using NRF52832 MCU , where in it is used for collecting vibration sensor data for about specific duration.
like...
