Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Recently got my Nordic Thingy:52 which is based of nRF52832. I wanted to test sending the data to cloud, so I just followed the IFTTT tutorial on the Android Nordic app. I...
For a design consulting client, they have a startup problem and need to know the approximate leakage current when a GPIO is in "DISCONNECTED" state.
I know the NFC pins...
I am using Uart Ble example of sdk , i want to write to Tx without UART can u please help me do it
i actualy want to send accelerometer data which is of size 40kb after...
Hi, I have added BLE custom characteristics in my application. I am writing and reading some values through ble scanner mobile app. Here i observed that when i enter string...
Hi,
I trying to use higher MTU size for my application and i have followed the att mtu throughput example. it is working fine upto 50 bytes packet size but when i try...
so, after getting it to compile, now i can no longer write to flash memory and i don't knwo why i am getting this error now. now sure if it is a result of nrf_dfu_flash and...
hi.....
i am interested in Mesh ,actually i want to understand the flow of mesh program (eg light switch example )how does it work,how it transferring from client to server...
Hi all,
In order to lower the power consumption of my device I have been experimenting with WFE. When using WFE I see that the interrupt latency is increased from ~4µs to...
Onl
I have 40 kb of data i need to send, and what i thought was using notification by creating a timer, which will be started as soon as device gets connected, in...
I am trying to interface with a I²C OLED display using Zephyr’s SSD1306 driver. The driver uses i2c_burst_write, which itself requires that i2c_transfer support gather writes;...
This is on SDK 15 : Not all services are reported when doing service discovery on more than one connection at a time.
Basically, ' ble_db_discovery .c' uses ' m_pending_usr_evt_index...
Hello, I am using the nRF51422 Development kit with SDK11. I am using the proximity application for the battery level service. I would like to strictly advertise to a single...
Hi,
I have an application where I have for example 5 BLE transmitting devices . Each device has one push button and each device is assigned to a number 1-5. I also have...
Dear nordic,
I am new in this open thread i tested your examples its working fine. i also tested CLI example i think its working but i didn't see a response in terminal...
I have a few Bluetooth transmitters based on nRF52832. My receiver devices are mainly iOS and Android mobile devices. I'm considering of replacing them with nRF52840 for Bluetooth...
