I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
hi.
As the manual says,It waits for an application event. and is called in the main while loop.
Does it mean that if I put some other routines carrying out polling function...
Hello, I am interested on nordic devices that support: 1) 802.15.4 (eg. Openthread) 2) secure storage for storing keys (e.g LWM2M credentials) 3) zephyr - rtos
I have seen...
Hi, we have a nRF9160 DK where we have uploaded the AT_CLIENT example on. Have tested the board and it works fine, able to send AT Commands and join to the network etc......
Hi,
I want to store scene when long press one button and recall scene when short press. I have done some changes but not able to achieve it, i am not sure if i should...
I was looking at this compatibility matrix, for SD and SDK.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52832%2FCOMP%2Fnrf52832%2Fic_rev_sdk_sd_comp_matrix...
Greetings!
we are using nrf5340dk to communicate with a Nucleo shield that has LIS2DW12 accelerometer on it (shield is X-nucleo-IKS01A3). We have a problem communicating...
Hello, I'm beginner for nRF52.
I saw examples about entering DFU by button and buttonless.
Is it also possible that changing the boot mode by a gpio pin which controlled...
Hello all, I'm working on ADC and data transmission.
Device do ADC first, and send those values.
Sampling frequency of ADC is ~80 kHz (sampling per 13 microseconds), and...
Hello,
We are using nrf52805 for our project. Facing some errors like "GATT ERROR" and GATT INSUF AUTHORIZATION and GATT CONN TIMEOUT ERROR" when I want to upgrade my application...
Hi,
We are developing our product based on nrf52382. In the scope of the certification testing of our end product, the test laboratory asks me if the Bluetooth low energy...
I am currently building a dynamic multiprotocol application (Thread+Bluetooth LE) with the nRF Connect SDK. For tweaking coexistence I would like to limit the length (=duration...
Hi,
In nwp-036 page 7,here is the AOD sketch map as below :
As fat as I am concerned, the Transmitter and Receiver should be reverse ?
Or there is something I misinterpreting...
Hi,
Background: I am looking at interfacing nRF21540 (FEM) with nRF52833 (Host) - hoping there's Zephyr support available for this(?)
Question: Product spec for nRF21540...
I'm trying to find the address of an attached twi sensor by using the twi_scanner. It worked on the default pins
but when I change the pins like this
It simply doesn...
Dear Nordic team.
We have to add new sensors using I2C protocol on our previous project.
Can i configure WDIO and SWDCLK pin to I2C pin?
If possible, i will reuse my...
