Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
I've recently enabled the watchdog in our project which included buttonless DFU. Project is based on FreeRTOS, SDK14.0, S132 v5.0.0 on custom board nRF52.
Since the...
Hi All,
I'm running a windows box with Android studio with the GitHub Thingy Repo https://github.com/NordicSemiconductor/Android-Nordic-Thingy project downloaded. The project...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about SPIS and SPIS event "NRF_DRV_SPIS_XFER_DONE".
1. What would trigger event...
HI,
In need to generate a sweeping tone to drive a piezzo element, i determined the tone should be sweeping back and forth between 2.5KHz and 4.5KHZ at an approximative...
My ultimate issue is trying to get a bootloader working on custom hardware with an nRF52832. The bootloader is mostly the base UART DFU bootloader from the Nordic SDK, with...
Hi,
I'm able to run the DFU mesh from the quick guide and now I want to integrate the DFU into my application.
My application is based on the light switch example, so...
Please help me fix my computer to allow nrfStudio to program pca10056.
I just received 2 pca10056 1.0.0 2018.35.
I am on 2 computers A and B: both with windows 10 64bit...
I trying to debug an interaction between using SPIM3 on the nRF52840 and the BLE stack in the SoftDevice . A reset is happening, which I think is being generated by the SoftDevice...
Hi I have an application where ESB will be used in the same environment as a few BLE devices which are also our devices. My plan is to set an rf_channel for ESB and then at...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
Hi, I can normally log with NRF_LOG_INFO(). But if i enable softdevice (bluetooth stack init) logging stops working. Interesting part is that there are several log lines before...
BLE Control by Main CPU (MCU):
1. How the MCU communicates with BLE HW?
2. What is the amount of MCU performance is required to control the BLE? (expected answer example...
Hi nordic.
I use SDK 14.20 and nrf52840 board and s332 softdevice.
Our app has to use ant+ and ble.
My device connect with app.
App requests device to ant+ scanning...
