Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello DevZone support team!
We are right now doing GCF certification of a device based on nRF9160 and need some urgent support from You!!
Attached is an excel sheet with...
Hi, I need more information about the GPS Chipset used in NRF9160 SIP or give me the name of this GPS module, so I can find its spec on the internet. Thanks in advance
I'm trying to activate because I want to use the HKDF of the nrf_oberon library. But when I try to compile with CMake and the target zephyr_final I get the following error...
Hello,
I am currently trying to program the nRF52832 to be able to receive data from a heart rate sensor. The sensor uses I2C communication and has an additional two pins...
Hi,
I am using this SDK: nRF5_SDK_15.2.0_9412b96 with NRF52840.
Having a disconnection issue where the device disconnects after one hour, If there is more devices connected...
Supposing that I broke off the nRF current measurement pin connector on the nRF9160dk - what are my options i.e. are there other pins that can be made available for the purposes...
Hi support team,
i'm using nrf dongle 52840 to update firmware for orther device, but somethime i can not able to access to send some command until hard disconnect from...
Hi,
I want to connect to Google Cloud IoT and for that I would like to generate the needed credentials on the nRF9160.
I need these ones , but the private key should...
Hi,
We have a strange issue. We have got two nrf52840DK(PCA10056, 2.0.0, 2019.47). The nrf52840DK board is not getting powered up after the board rested in off for a long...
I am following example in https://docs.edgeimpulse.com/docs/nordic-semi-nrf5340-dk but I cannot connect nrf5340 to EdgeImpulse studio . When I connect device via usb cabel...
Hi,
We are developing an IoT sensor application using nRF52832 dev kit as a starting point. We have a sensor that we need to read once every second for 10 milliseconds...
I am using the simple code below to generate a signal from a memory buffer. I cannot generate a signal cyclically. If ONE sequence is used, then the buffer is played once...
Hello,
The flash memory of my existing project originally occupied about 200kb, but suddenly the capacity increased to about 255kb.
So I checked and found that the amount...
Hi
I'm doing a project using the TimeSync library (latest version) on 2 nRF52832 development boards.
I've ported the library to my project, the time synchronization...
hi, all. I'm using nrf52833, pca10100, s140.
The flash memory capacity has increased, so I checked the memory, and it seems that the log values have been saved.
It should...
