[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi,
I would like to combine NFC - BLE pairing and launch app record. Naively I thought I would write the second data right after the first:
But this does not work. Reader...
I am using an NRF52832 on an energy harvesting board where lowest power is critical. I can achieve ~2 uA current consumption in idle state (waiting on RTC interrupt), wake...
Hi,
I work on the nRF52840 DK with the ble_app_uart example and I want to add a timer using app_timer api,
in order to create RTC time/date timestamps for my sensors raw...
Hello
I am using SDK15.3 and nrf52832 development board.
In my setup,
1. I have a few peripheral nodes whose only job is to transmit some arbitrary packets ( say P)...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
Hi all,
I am working on the Smart remote and when "spamming" a lot of key simultaneously, I sometimes get a warning "m_coms : packet lost" and then a disconnection.
...
Hello,
I have a Taiyo Yuden EYSHSNZWZ module. I also had a breakout board manufactured for it to get access to all the pins. I am having trouble trying to program the...
Hello,
I`m trying to get this ( https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role/ ) working properly to test the possible working range between two nRF52840...
To the kind attention of the Nordic support team,
Hi to you all, I have got legacy gazell code running on nRF24. In old code the following instructions was used:
hal_nrf_set_address...
My customer wants to do a range test with a propritary 802.15.4 software.
Do you have an example for the nRF52840DK with an blinking led if the communication is established...
Hello,
i want to display a string in 5x21 led matrix using HT1632 Led driver
Using SPIM0 Protocol i should send data from nrf52832 to HT1632 led driver
My question is...
Hello,
I am working with the mesh SDK 2.1.1 version and the Light switch proxy server and proxy client examples.
Everything is working fine between client and server...
Hello,
We are designing a board based on nRF51422 and we are working with a company based in a different country for Android/iOS app development. They bought a nRF51 Dongle...
I have downloaded the latest nrfgo, but the version of jlink is 5.12V.jlink5.12 does not support nrf52840,so i updata it to jlink6.40,however nrfgo still can't download the...
