Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I'm very new with nordic environment. i would like to modify the FDS address because it seems it is always put to the end of the flash and when i flash a new bootloader...
Hello,
I'm flashing a bootloader (DFU) and then i'm flashing my application but each time i flash the application, Segger Embedded reflashes the softdevice and the MBR....
When building the sample code using the latest SDK I do not see the device in the device manager and after a while I get this error:
Any hints on what is wrong ?
...
I have already made a post for this problem. Initially, Amanada Hshei gave some troubleshooting techniques and it did not work out,
Here is the original post, and My request...
Using Windows 10
Master Branch
Compiled using Segger 4.16
Downloaded merged.hex
When running NRF Connect Link monitor and connected to nrf9160
I receive the following...
HI,all
I have tested ZC and ZED to establish network,I found a method zigbee_erase_persistent_storage(bool),when i put true on ZC and put false on ZED, first time they can...
HI,all
I am a newman for zigbee on NRF52840 with S140 softdevice,
I have two board, one is ZC and another is ZED.
On ZC board, I use ZB_GET_OUT_BUF_DELAYED2 to send...
I am using sdk15.2.0 with PCA10040 dev board.
In ble_app_eddystone example, the configured advertising interval and duration dont match the observed values.
I think I...
Hi Nordic,
I have recently received an error from pm_init that I have never seen before, NRF_ERROR_INTERNAL. After some debugging, I found it was really due to NRF_ERROR_STORAGE_FULL...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi Team,
I transplant the project Uart from example/peripheral/uart tranplant to blecentral/multilink project, but it does not work, it indicate that APP_UART_COMMUNICATION_ERROR...
Hello,
In below link, I am bit confused between “With bootloader” and “Without bootloader”. What for this bootloader.
https://infocenter.nordicsemi.com/index.jsp?topic...
Hi all,
I purchase a Li-Po batter where it will output 4.2V when I connected to nrf52480 DK, it causes all 4 LEDs (LED1, LED2, LED3, LED4) not functioning anymore.
The...
Hi,
I have the latest 0.4.0 tag, flashed the latest modem firmware 0.7.0-29.alpha, and debugging the asset_tracker app under nrf9160_pca10090ns.
When I debug the app it...
