Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
I'm trying to discover a vendor specific service that has 7 characteristics. However, when I increase BLE_DB_DISCOVERY_MAX_CHAR_PER_SRV to 7 , ble_stack_init() hard faults...
Is it possible to use PPI and RTC to turn the HFCLK on or off ? (external Xtal)
Example - something like this ...
NRF_PPI->CH[9].EEP = (uint32_t) &NRF_RTC0->EVENTS_COMPARE...
hello,
when I use the chip nrf51822(3rd generation),I find that when I open DCDC function,the ability of chip receiving msg is weaken.the receiving distance is shorter a...
I am doing a blob read on two s130's with s120(central). I am getting BLE_GAP_EVT_CONN_PARAM_UPDATE event while doing a continuous blob read.
Some times i get BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch...
Using a nRF51822-QFAC-A1 on the nRF51-DK I noticed unexpected behavior when starting the HFCLK and LFCLK in rapid succession. This variant reproduces the problem at startup...
I would like to have 31 bytes for my own in advertising and so far I have disabled everything except adv_flags (it still takes 3 bytes cause of length, AD type and value)...
Hi there,
just wanted to know what the practical differences between the JLINK and mbed MCU interface firmwares are.
From what I experience I can only use the UART over...
Hi,
I'm writing a service to send indications on a couple of characteristics that are part of a service. In order to determine whether indications have been enabled or not...
Hi,
Is there a smaller version of the desktop 2 firmware? I don not need firmware for NFC only ble 4.0. Also would like less complicated pairing. The 6 didgit code is unnecessary...
Hi , I tried to change the transmission power using the s110 API and tried checking if the value of the register storing the transmission power is changed or not. Following...
Hello,
I'm trying to create my own bootloader application that uses softdevice in IAR. I would like to know how to configure my project so that it writes 0x0003A000 to...
Hi all,
I've a problem using pstorage: after I execute a pstorage_clear, my ic (i have the pca10028 board) go crazy, the application I've write stop execute and I can't...
