Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
S110 v8.0.0
SDK v8.0.0
ble_app_uart example
I first initialize the services and then initialize advertising. Everything works fine when I do NOT advertise the...
I'm currently trying to make an application using the development kit & I'm trying to use the timer driver, when I induled the C & H files of the driver I got an error : ...
I'm trying to compile the ble_app_beacon_s110_pca20006 project in Kile uVision5 and I get the "cannot open source input file "core_cm0.h": No such file or directory" error...
I am trying to run a NRF51822 chip using Emblocks and OpenOCD, the debugger interface is a ST-Link from a Discovery board, which supports SWD.
When I program the Blank...
Hi,
I bumped into a problem trying to get PWM working and traced it back to the app_pwm_init function, for a simple test case use the the pwm example in the 8.1.0 SDK and...
Hello everybody,
I'm currently trying to start with the nordic development kits, I installed all the tools required to be able to start the development & also I get some...
I am trying to persist characteristic data written by the central side after on_disconnect . I can see the data written inside the evt_write->data ptr and I copy it to store...
Hi Nordic Expert,
Recently I wanna run ble_nus service on my nrf51822 platform, you know, sdk 6.0 does have this demo code in s110 directory, but from sdk 6.1 I cann't...
I'm trying to connect to/program my nrf51822 module I just got. I've got it set up with my st-link but whenever I try to flash the device I keep getting: Error: Flash Download...
I'm trying to enable basic commands with my device. Ideally I have a terminal open on a mac running nodejs or use the UART subapp in the nRF Toolbox App, type a special command...
What's the proper way to debug what's causing my eval board to reset? I'm assuming I need to put a breakpoint in the hard fault handle, but how do I trace that back to the...
Hi,
as a university project, I am currently developing a ultra-low-power temperature and barometer sensor powered just by RF and laser-beam energy. Please see this link...
Is there any document that describes what has to be done in the App code to migrate from i.e. SDK v7.2 to the latest 8.1.1? I could not find it.
Ideally it would be nice...
I try to add a custom characteristic value's UUID. I couldn't find any example or document that provide this information. All I can find is a function sd_ble_gatts_descriptor_add...
