Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
NRF52840 - SDK 15.0 - Tested with Softdevice and No Softdevice
We have an application that requires deterministic execution of a group of SPI transfers over EasyDMA, where...
hello everybody!
i want to sample an analog signal with the board and send the 0/1 data with ble to the receiver .
i created my on service with rx and tx like in ble uart...
Hello Nordic Expert,
I am facing a stall pid issue with nRF52840 Dongle using nRF5_SDK_15.2.0_9412b96. The chip build code is QIAA C0 . I started with usbd_hid_generic example...
I have an application with Nordic devices as Central and Peripheral.
The first device is a multi-protocol device (nRF52840) and acts as BLE peripheral. Min connection interval...
Hello
System:
OS: Windows 10 x64
Application: nRF Connect 2.6.1 (with Bluetooth Low Energy 2.2.0 and Programmer 1.0.2)
Problem:
My device is connected to the COM7...
Hi,
I currently have a custom board with an nRF51422 on board. I am considering upgrading to the nRF52 series. Are there any nRF52 models that are pin compatible that I...
Hello,
We are working on a network of low energy sensors that work without connection. The sensors have a configurable service, so from time to time it makes itself available...
Hi,
I'm trying to implement Buttonless DFU into an existing BLE application. I'm using nRF52832 V1.1.0 boards (one for the BLE peripheral running the application and buttonless...
currently i am running ble_app_uart_c example from sdk15.0 and i successfully discover one of the custom service.now i want to discover all the services provided by peripheral...
What is the output for the capacitive sense driver example? ADC code? Voltage? Time? For example, when the csense_handler function is called, the following line will print...
Hi I'm facing problem to detect external crystal oscillator in my custom nrf52832 board's. I'm think it is not connection issue as I'm facing same issue in other 9 boards...
Hello, everybody.
I'm working on combining the nRF52840 and the GPS module and are currently developing a program that stores real-time GPS data in an external flash memory...
Hi,
We are planning on upgrading the firmware on our device from Mesh v0.9.2 to Mesh v3.0.0 via BLE.
Specifically, our current stack uses: - nRF5 SDK for Mesh v0.9.2 ...
IPhoneX sometimes goes into the ble_evt_handler auth_status event, and then p_ble_evt->evt.gap_evt.params. Auth_status.auth_status!= BLE_GAP_SEC_STATUS_SUCCESS, other iPhone...
