Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Using ble_app_hrs running on a PCA10004 (nRF6310 motherboard + PCA10004 which uses a PCB antenna), the achieved range at +4dbm (<10m) seems to be short. Master Control Panel...
I think the new MCP might have a bug somewhere. I have not been able to find out the exact sequence on how to provoke it, but I have to restart the application more often...
if I set BLE_GAP_CONN_SEC_MODE_SET_OPEN, I can get data,
but if I set BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM,
Three different even sequences happened, only one sequences...
Hi,
I disconnect the BLE by calling *sd_ble_gap_disconnect*(), and found that it run to *app_error_handler*() after the BLE_GAP_EVT_DISCONNECTED event occured, and I don...
I program the nRF2727 module with the "Block readback of mainmemory" seleted using nRFgo studio tool.
After that, I can still read out the content of flash. What's the root...
As per this thread: devzone.nordicsemi.com/.../question-regarding-hfclk-control the SD stack takes care of HFCLK, however as fas as I understand HFCLK is also responsible...
Hi,
I use the DTM for the production test, I use the transmitter test ,with canal 19 (frequency = 2438MHz).
What is the tolerance of the frequency do you recommend (Min...
Hi all
i am working on Student Response System in which there multiple Transmitter and one Receiver and i want Receiver(nRF24lu1p) to behave as HID device.
Can any one provide...
I just buy a set of nRFgo starter kit . One pin of the display module (nRF6350) was destoryed, and the correspoding hole of P6 in the motherboard was inserted with short pin...
Hi,
I have some questions about how BLE scanning works that haven't been answered clearly anywhere I can find, (except no-doubt the Bluetooth Spec/Tome):
What...
You can not build out " the arm c c + + compiler has stopped working " in Keil uVision5.
PC of lenovo made in (Windows7 environment ) ,
By introducing development environment...
Hello everyone,
thx in advance for answers.
there is limitation written for 6.0.0 as follows:
Synthesized low frequency clock source is not tested or intended for use...
