In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
hello all,
i am a begineer to nordic . i am trying to read adc PCF8591 value through TWI and i want to print the value in UART TERMINAL.
i have written the code. but...
Hi,
Im trying to connect ble_app_uart to my gsm module. For some reason program fails at runtime. I was expecting to find a filename and line number where the error has...
Hi,
nRF52 Board, S132. Now, I want 6 pwm, 6 adc .
nRF52 has 5Timers, Timer0-Timer4.
Now, I allocation these timers as follows:
//TIMER0 is used by softDevice
APP_PWM_INSTANCE...
Hi,
I want to access restricted peripheral: TIMER0.
After small research found that I should use sd_ wrappers, in my case sd_nvic_SetPendingIRQ(TIMER0_IRQn) however I...
Greetings,
I'm working with LPCOMP to detect a signal. This signal is the output of an opamp amplifier. What is happening is that when the LPCOMP is switched on there are...
Hi,
I am using SHT21 Temp sensor via TWI manager. As per the spec shown in the image
I have to add 20us delay between the sensor ACK and STOP command.
Is there any...
Hello, I have the Beacon Development board and the sample firmware downloaded and up and running in the Keil MDK IDE. My specific application requires some code to execute...
Hi,
i want to add a current time service to nRFgo. In particular for the glucose measurement profile.
Any suggestions for this???
I add manually the current timer service...
Custom nRF51822
SD130
SDK V11
So sometimes my disconnects seem to fail, the return code says success, but when I try to reconnect I get an error 18, NRF_ERROR_CONN_COUNT...
Hi,,
In the GPIOTE example code(I use TIMER2), I want to control the cc register values by accessing the TIMER2_IRQHandler routine. I tried enabling the interrupt for compare...
I found there is no ble_app_hrs_rtx PCA10040 ,
and release note said:
nRF5 SDK v11.0.0
Heart Rate Application with RTX: Support for nRF52 has been removed.
...
Hello,
I have some MDBT40 modules from Raytac that are blank. I want to flash some code (anything at this point) using the STLink/V2 programmer , SWD interface, and OpenOCD...
So I've got my device running, set up two services with some read and write characteristics and it all works like charm now.
But now I want to react to values written into...
I am using GPIOTE to response to transitions in some GPIO pins. This code is added to the BLE UART example code (ble_app_uart_c with S120) from SDK 10. The code is already...
Hello
I have some trouble with my DFU bootloader, because I changed the BOOTLOADER_REGION_START.
This is, because I need some more space for bootloader.
Do I have to...