I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I have configured the nrf52840 DK one board as Peripheral and other as central.
Added multiple services and characteristics. I am sending some data at every 20ms using notify...
Dear all:
Customer products in normal mode, BLE works normally, all functions are OK. An error occurred in DTM mode during authentication. Procedure The failure status is...
Using the SDK 15.0.0 SPI example (master) to send a single byte.
Sending 0x00:
Sending 0x01:
Sending 0x02:
Sending 0x04:
etc ...
Sending 0x7F:
In all the...
I am working on a module MS12SF1(nrf7002 + nrf5340) module. I am getting uart data from another device to this device through uart. Earlier when I configured uart to its by...
We have some custom hardware that acts as a peripheral, and currently has the advertising data packet set up as follows:
BT_UUID_SPD_SERVICE is our custom 128-bit UUID...
Hi.
We moved to version 2.5.2. Here we encounter some problem with data mode. Sometimes we don't get response of exit from data mode.
We publish data, after we send "...
Hello Everyone,
I wanted to ask if there is a way to use SonarCloud for analyzing a firmware based on the nordic toolchain v2.5.2, I understood that I have to set up the...
The MDS service supports the chunks through Bluetooth GW. in reality this is not of much use in real scenario. So is it possible to upload the chunks directly to memfault...
I am running the demo of "nrf-knx-iot/samples/light_switch_actuator" on my customized board based on NRF52840.
I could burn the light_switch_actuator firmware into this...
I posted my configuration in a separate discussion .
Calling this method works when CONFIG_BOOTLOADER_MCUBOOT=n works. But as soon as we flash an image with MCUBoot enabled...
Hi Support Team
We add below code to the while loop in the main.c file of NCS sample https_client to post data to server. But it can not recover to post data to server...
I'm trying to import the native libraries to Xamarin forms, I need for the FirmwareUpgrade section of the iOSMcuManagerLibrary. I compile the example project correctly and...
Hi,
I'm using the NRF52805 with the QDEC.
As far as i saw in the datasheet, the QDEC suppose to take about 5uA But when i operate it is takes about 500-700uA !!
...
Hello,
We need to use some fixes that aren't released yet in a version yet. Specifically, an MCUBoot fix: github.com/.../303
Is there a guide as to how to use forked version...
If I purchase a Zigbee endpoint device off the shelf (for example an SOS button) and I added to my nrf Zigbee network(routers and coordinator and other endpoints I have developed...
