Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hey there
I am trying to get the Radio test example to work with NRF52832,
Using Keil IDE,
however resources seems to be removed,
any solution for that?
I have a custom board with a GPS chip and trying to communicate via UART2 on a nRF9160 using NCS 2.1.2.
When I try to write to the UART, the board reboots with no error...
I am porting an existing application from NRF SDK v17.1 to the latest NRF Connect platform. Application is primarily a BLE advertisement scanner on an NRF52833.
On our SDK...
Good day
I have noticed that when using a callback functions certain limitations exist. For example, adding functions to the callback function will run into an error or...
I am working on a BLE mesh project, and I have created my own BLE mesh publish and send functions,
My concern is, I am creating buffers using the bt_mesh_model_msg_init...
Hi,
This is a continuation of the below tickets:
After updating the modem firmware to 1.3.3 and recompiling Asset Tracker v2 with SDK 2.1, I'm afraid the problem...
Hello!
I am trying to connect my Thingy91 to nrfCloud, but after successfully activating the SIM card, I receive error 40412: No device found for this id. The device has...
Hello Team,
I am trying to develop an app with BLE example as the base and modifying it.
Hardware setup:
PC - Windows 10, nRF Connect launcher v3.6.1, BLE example...
Hello all,
Currently, I am trying to set up debugging functionality for a custom board using the JLink Plus. When I use the JLink RTT Viewer, I get the following:
Other...
hi team,
i have trying to wrote a code for analog to digital converter module in segger 5.40 using nrf52840 controller and and i found one example code related to analog...
Hello,
I've a "follow up" issue related to this ticket:
In an earlier state of our project, we've adopted the smp_svr application as our "DFU".
But during maturation...
Hi there,
We are running a power consumption test using PSM mode, and we are however not measuring the 4uA floor current as expected.
We are requesting a active time of...
Hi Sir,
I want to test advertising extensions feature with zephyr hci_usb on nrf52480.
Have any user guide to reference ? ex. linux hcitool or btmgmt commands.
Thanks...
Hello
I'm currently writing a program for an NRF52840 chip which reads some values from an ADC each second and writes them to an external flash chip. I'm trying to run this...
Hi Nordic support team,
nrf sdk for mesh 5.0.0, nrf sdk 17.0.2, nrf52832,
When I config the tx power for the mesh msg transmission I faced a problem. I found that there...
