Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Hi, I am using Heartbeat messages with the light switch example, and want to log the nrf_mesh_rx_metadata_t in heartbeat_opcode_handle() to RTT viewer so I can write it to...
Hi,
if my device (nrf52832) is in application and I perform firmware upgrade using nrf connect and PCA10031 on Win 10, the upgrade process is very slow (0.35 kB/s). I stop...
Hello,
I have a following requirements,
Build a custom bootloader which accepts DFU through OTA and UART.
this boot loader must also contain softdevice , so that finally...
I'm having problems with toggling the EXT0 pin on my thingy:52.
I have tried with setting the EXT0 as an output like this: drv_ext_gpio_cfg_output(SX_IOEXT_0); And then...
This is not really a problem - more like an enquiry
Is it possible to gate PWM output using another GPIO pin e.g. if the second pin is low then so its the PWM otherwise...
Hello,
I would like to test and adapt the example "ble_app_uart_coexist" with my nRF52840 DK. Unfortunately, I believe that this one is only intended for nRF52832 and softdevice...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Hi,
I'm using custom board with the nrf42840 and I need to use p1.09 as a GPIO.
How can I do this in a debugging mode (using the PCA10056 as a jlink)? Can I get a code...
Hi,
I want to get interrupt on GPIO using gpiote module.
I searched for example but couldn't get it.
Can you guide me how to use gpiote in nRF9160 ?
Regards,
Smitesh...
Using Fanstel BT832A BT 5.0 Module which utilizes SoC nRF52810 QFAA
1) Yes or No: can I configure a GPIO as a Timer/Counter Input so I can feed a high frequency input into...
Hi,
I just wanted to know which flash is used by the flash manager within the SDK Mesh v2.2.0 onoff client/server examples ? Is it the 1MB internal flash or the external...
Hello,
During development of a custom board, based on the BMD-300 module from Rigado, which uses an nRF52832, we ran into a SoftDevice fault under specific circumstances...
Hi,
After trying to work out why one of our nrf9160 DK:s cannot execute any AT commands using the at_client sample I tried redoing the getting started guide to make sure...
Hi, I am making my own bluetooth custom board with nRF52832. Till now, I made my custom pcb following the infocenter layout and chip antenna like below.
Now I want to...
