Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Using Rowley Crossstudio for ARM.
Using SDK V15.3.0 and S140 V6.1.1
When calling sd_softdevice_enable(..) it returns 0x1001 ( SVC handler missing ). Any suggestions ?
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
At present, I have a project that needs to add dual uart function, but 52832 does not have hardware dual uart function, so I need to simulate one serial port, I need your...
Hi all. I try to implement ble dfu bootloader project via getting start from SDK/examples/dfu/secure_bootloader/pca10056_ble_debug project.
Using:
OS: Linux
Compiler...
Hi!
This is a general question about iOS app distribution, but it regards our use of Bluetooth Mesh. I know it is each company's own responsibility to make sure they comply...
Hi there,
I am porting existing code from nRF52832 to nRF52840, and found that bootloader references to NRF_BPROT fail:
Apparently becuse the nrf52840.h in the mdk does...
Hi All,
I have loaded in the Bluetooth Mesh Light-Switch example and it works well.
For now, I would like to read out the received data from the switch node (client) to...
Hello! I am using SDK 15.3.0 to develop the NRF52832 firmware. At present, I want to implement a function, when the device is connected to the IOS host, start pairing, and...
hi attached code for below requirement:
command: scan on - scan devices
command: devices - display filtered devices .
Filters set are for : thermometer, NUS and custom...
I am using the TWI manager to schedule transactions with a number of sensors, over two seprate twi instances, and then sending that data over Ant.
The twi manager scheduling...
I am using the NRF52832 chip on a D52M M8 module, and SDK 15.2.
I have a number of sensors that I am communicating with over TWI using the TWI Manager on two separate channels...
Hey
I am working on ble_app_blinky central and peripheral, I want to calculate the RSSI of peripheral after connection with central. I am able to calculate the RSSI value...
At the end of last year, the new package nRF5240 WLCSP was delivered and it is now available in the market, however, I have not found an official layout for this new package...
