I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello all,
I am currently using the SoftDevice Handler library to enable/disable the SoftDevice and observe requests and state transitions on nrf52832 with SoftDevice S112...
I need maximum throughput in nrf52832. So i enabled DLE and using s132_nrf52_5.0.0_softdevice. The data packet length is 96 bytes in single packet. Conn interval 7.5 and 10ms...
I Can't set nRF5 SKD Root Path to: nRF5SDK=C:/nordic_semi/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96
I created a global macro as instructed (many times) but the path...
Hi there!
I'm using nrf9160 DK's SiP to establish TLS connection to MQTT broker.
When I call nrf_inbuilt_key_write it returns 13 error code which means "If the operation...
Hi everyone.
In mesh light switch example., i try to add timer0 (or any timer).
After initialize timer, application always jump to timeout event, and i don't know why...
I am developing based on ble_app_uart example of SDK12 for nRF51 DK and I need to switch BLE off completely when power disappears to save battery and switch back on when power...
After reading the document for nRF52840 Radio Peripheral. I have a doubt about LENGTH field in packet format. what is the difference between LENGTH field and STATIC_PACKET_LENGTH...
Everything works fine if i use the default baudrate
NRF_UARTE_BAUDRATE_115200 but if i change it to 250000 or something higher the applications starts and goes directly...
Hello ,
I want to read around 6 analog pins, not necessarily simultaneously. I could afford some delay in between them. i am using nrf52832 dev kit with sdk 15. How do i...
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.3.0/nrf/gs_programming.html#building-with-ses
I am following the example at the address below.
However, the following...
Hi,
This error has been bugging me for few days and I still have no luck in troubleshooting it.
Recently, I just changed my work project from nrf51822 device to nrf52832...
Hi DevZone members,
I would like to output the elapsed seconds as a floating point value using NRF_LOG_INFO. However, nothing is generated for the floating point value....
I am interfacing nrf52832 with TI TRF7960A using SDK 14.2.0
According to Application Report ( http://www.ti.com/lit/an/sloa140a/sloa140a.pdf) ,
when receive data, SPI...
