I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Dear all,
I have 10000 devices and I need to put a different value for every device, but I do not want to create 10000 firmware.
Is possible to do that with a tool? I...
Thanks for the reply. I can program my custom PCB from the nrf52 but I can't program the on-board nrf52832. It is always looking for Jlink to an external board. What tells...
I would like to modify the way the SPM is built, specifically by setting CONFIG_BOOT_BANNER=n but do not want to modify any files under the ncs directory. I tried the solution...
I have a multi peripheral sample I am trying to make work
I do a
BLE_NUS_DEF(m_nus) and BLE_HRS_DEF(m_hrs)
this will register two event handlers.
When an event occurs...
I have downloaded nRF5_SDK_12.2.0_f012efa and tried to test logging in examples but without success. Even if I compile an example where NRF_LOG_BACKEND_SERIAL_USES_UART 1...
Hi,
I'm trying to use an nRF52840 Dongle to make measurements from 4 SMT172 temperature sensors.
I developed a proof of concept on an nRF52840 DK, where I connect all...
Hi,
Finally i am able to build a basic TCP/IP server client, attaching the project here , i have some questions wrt modem and TCP/IP stack:
I see two different socket...
Hi,
I'm trying to increase Zigbee Tx Power to +8dBm by using the function nrf_802154_tx_power_set().
Digging into the code, I see that it is calling nrf_802154_pib_tx_power_set...
Hi,
I am using NCS 1.2 with Zephyr SMP_SVR example compiling with my own board DTS and using MCUBOOT
I have my own partitions configured in my DTS (attached down at the...
So I'm trying to start off development of my project using the PCA10040 development board. I have downloaded the SDK16 and built a couple of examples no problem using SES...
Hi,
I have a question regarding the frequency of the SPI peripheral of the nrf52.
According to the Product Specification v1.4, the minimum value for the frequency is 125kbps...
Hello Nordic Support!
The stop bit of the last character is short in the Uart output part, and the other MPUy cannot receive the character. How do I fix it until I send...
To the kind attention of Nordic support team,
I was wondering if it is mandatory that Host and Devices share the very same frequency table, with same size.
Is it possible...
Hello,
Because I have no space for additional transistors on my board I made a design with nrF52840 and rgb led connected to 5V.
Configuration o GPIO pins:
H0D1 Value...
