I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi I have run a few peripheral examples ok and now move to evaluation of ble_peripheral also.
I'm using this version of the SDK....
If I program the softdevice and...
Hi
I am using Segger Embedded Studion on Linux 16.04 operating system. I have programmed softdevice, i.e, I have provided SRAM and FLASH START VALUES and other things. How...
Here is a list of problems I found. Please fix them.
nRF SDK 15.3
Examples: logging does not work in examples. I think the problem is related to this issue .
Documentation...
Hi there,
On my application, I have multiple sensors attached to the nRF52 and I read them every 5 seconds scheduling the read inside a timer handler, then when the Softdevice...
Hi Nordic Forum!
In the past, I set connection interval min to max is 20ms~75ms, it work ok for IOS。But on Android platform, Android use 75ms as actual connection interval...
Usually if i am making C Program then i just include the library and get on to the code using documentation. this is same case when i am using STM32 , Samd and esp32
but...
Hi
For a project I want to send acceleration data via BLE 4.2 (with DLE). An acceleration packet consists of 81 values (24 bits each, total 243 bytes). My goal is to send...
Good day
I converted a Central UART example. I thought I would experiment with the "sd_ble_gap_tx_power_set()" function to see how it works.
When I include the following...
nRF5 SDK v15.2.0, nRF52840
This issue occurs on reset, most often after cycling power.
There are 4 pages reserved and 4 data pages are found. Since a swap page isn't found...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
Hi,
My current project make use of pairing/bonding and at certain times I change the attribute table. To notify the central device about this change I have added the Service...
I am working on NVMC. I was going through the product specifications for the NVMC. In that, it's given that the number of write operation limit is 181 for a block in nvm....
I'm trying to get the PPK working when connected to aNRF52840-DK, but getting the error - Error while setting up device [REDACTED_SERIAL]: Error occured when close opened...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0 in my customboard.
As peripheral, device communicate Ios phone by using ble.
However, my device sometimes...
