In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Connectivity board crashes after a few seconds of sending/receiving packets really fast with the following:
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at ../nrf_sdk/components...
NRF52
I have a Transmitter and Receiver. The Receiver starts and listens to the ESB.
The Transmitter starts, sends a message on the ESB and restarts. The message is static...
We are in the progress of finalizing our first Bluetooth products, based on nRF52840, S140 6.1.1 and SDK 15.2.0. We have gone through the listing process (Launch studio and...
DFU failed on nrf52832 with my custom program that is based on coexist example and not failed with blinky ???
is there any frame loss for a big hex file that want to dfu...
Folks,
Using the HID mouse ble-peripheral example code as a base, I'm attempting to add SPI support, using the SPI example for pieces of code.
Both sets of code build...
I am trying to set up ack in my PTX so that when my PRX is off or out of range I get the case TX_FAILED event and when it is on and receiving data my PTX will get the case...
Hello,
I am looking into the nRF9160 hardware. And at the moment we are only interested in the lowest level possible.
The peripherals are well documented, as espected...
Hello,
I am working on TWI master application on a nRF51 board, with a sensor associated.
I have often a problem while the reception sequence.
My application:
-> nrf_drv_twi_tx...
The latest changes to the Secure Boot sample main.c file cause compilation issues;
new main.c @line 304 NRFX_PERIPHERAL_ID_GET(NRF_P0), 0);
Doesn't work.
old main.c...
SDK 14.2
nRF52832
The application I'm developing uses the flash memory to store parameters such as calibration parameters for the sensors on the product. I foresee that...
I start with the ble_template example (SDK 15.1 || nrf52382 || Embedded Studio for ARM 3.41). My goal is to transmit data (string or int) from a custom made PCB to the NRF_TEMPLATE...
Hi
I am back on the firmware end of my project after several months doing the PC and Xamarin ends in C#... Trying to remember my C...!
My device has 3 MCU's incl the...
Hi,
I am getting these compilation errors:
'NRF_DRV_SPI_INSTANCE_1' undeclared here (not in a function); did you mean 'NRF_DRV_SPI_INSTANCE_'?
'NRF_DRV_TWI_INSTANCE_0...
Though it doesn't seem to be mentioned in the product specification, I've confirmed the hint from https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/saadc_low_power...
Hello Supporters ,
I have built one application using NRF52 .in which i have interfaced sensors and Winbond[W25Q128FV] SPI Flash. now i want to store sensors data to SPI...
