Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello, I'm using SDK 15 and softdevice 6.0.
I use the micro as a master and I connected an i2c sensor as slave. I had put external 10 Kohm pull-ups, but I had a low level...
Hello ,
I am using SDK for mesh, I have saved .hex image file in flash.
Is there any example or any suggestion how can I run bootloader which will read data from flash...
HI:
Always error while porting,Error: L6218E: Undefined symbol app_uart_init (referred from main.o).
I added a path, and ENABLE UART_ENABLE 1 in sdk_cofig.h
Compile...
I have set up the gcc toolchain on Mac OSX to compile my BLE nRF51822 code and I tried to flash the code. Here are the 3 scenarios that I have tried (JlinkExe on Mac)
Case...
Hi,
I am not sure if this is the right place to open up a thread about a zephyr HCI firmware issue. Since Nordic also contributes to zephyr I'm putting up this question...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi All:
When I simulated PWM by GPIO, the output current noise was shown like the picture below (red circle area):
Cause it will lead to a loading issue in the backend...
I want to implement a long write. The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi Nordic team,
I have 2 nRF52840 DK boards.
I followed the steps mentioned in the below link, I am able to Transfer the DFU archive over serial with nrfutil(LED keeps...
I want to enable the Logger Module to have the high default severity of Error and then be able to enable lower level severities on an individual module for debugging. Is this...
Hardware used: 2 nRF52480 DK boards
I am running nRF5_SDK_15.0.0_a53641a\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput example, I want to increase...
I read zephyr official document of nrf52810 support：
http://docs.zephyrproject.org/boards/arm/nrf52810_pca10040/doc/nrf52810_pca10040.html
It describes like this : ...
Hello,
I just got my nRF52832 DK and am following the Getting Started at the Infocenter to get familiar with it. Running Ubuntu 16.04 and all the latest Nordic tools (SDK...
