Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello,
I'm trying to program the NRF5340 DK board on linux. However, the board doesn't show up when I run `nrfjprog -i`. It doesn't show up when I run lsusb. `udevadm monitor...
I'm struggling to get a Micron MT25QU128ABA ( https://media-www.micron.com/-/media/client/global/documents/products/data-sheet/nor-flash/serial-nor/mt25q/die-rev-a/mt25q_qlhs_u_128_aba_0...
Dear Community,
We want to use bonding to connect our app to the nRF and create a personal account.
So all your devices will have the same UUID. If the device never connected...
We're working on a board with an nRF52840 running BLE with softdevice S140 and SDK 17. The board has an external SPI flash, and when we realized that SPIM3 can be run at higher...
I want to know if I call the following function, which condition should I meet to determine that the coordinator is not connected to any terminal devices. For example, I now...
Hello, I am looking for some help or example code that describes minimum set of the files and #defines required to enable AES 128bit encryption and decryption using ECB mode...
Hello,
I'm trying to learn what might be typical latencies for Bluetooth LE Audio. For instance, the aptX low latency codec claims latency around 20-40ms. Is Bluetooth LE...
Studying the documentation for the nRF52811, I found a difference in the description of memory recording and memory erasure:
write: " The CPU is halted while the NVMC is...
Hi,
I have nRF52840 DK and am using nRF5_SDK_17.0.2_d674dde.
I am not using SoftDevice, and Zephyr RTOS.
I have a simple program and using RTC0 timer. My code snippet...
Good afternoon,
I have a question regarding the nRF9160 and the eSIM configuration. We have developed a prototype PCB based on the nRF9160 DK and included an eSIM. However...
Hello,
I am trying the example of ble_app_uart and when i am building the example it gives me an error RX_PIN_NUMBER undeclared. When i load the pca10056.h i can see TX_PIN_NUMBER...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b and FreeRtos
This device has some bindings already set...
Hi,
my zigbee network for 120 sensors. if i declare 120 install codes then most of them don't work. The "zb_secur_ic_add" function works without error, "zb_secur_ic_get_list...
Hello!
Following problem:
I try to save 100Byte uint8_t messages in the nvs on the nrf9160.
Sometimes it works and only some moving logs come up and sometimes the following...
