Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello,
I am currently using the nrf52840, SDK 17.0.2 and segger embedded studio version V5.34. I have been working extensively with the ble_app_template in the peripheral...
CENTRAL : nrf52840 DK -SDK 15.3 -SES 5.40 -s140
PERIPHERAL : Arduino NANO 33 BLE Sense
Hello, I'd like to deliver the Arduino's sensor data to DK board via Bluetooth...
Hello,
I am currently working with nrf52840, SDK 17.0.2 and Segger Embedded Studio V5.34. I have a custom designed bluetooth app that connects with the nordic device to...
I am using zigbee sdk to establish mesh network.
I am using client router example to fetch mgmt_lqi details where I am getting flag field in the response.
I want to know...
Hi,
The ncs/v1.4.2/nrf/tests/unity/example_test project does not seem to build for the emulated native_posix board when I try:
First it was complaining about Ruby so...
We am using SDK 16.0.0 with S132 v8.0.1 on an nRF52832 custom design.
We have ported the secure boot loader to our design and we can perform buttonless OTA.
The issue...
I am looking to use the L2CAP in the basic form. I see that there is the Experimental OTS example in SDK 17.0.2
this only uses the S132 Softdevice. I am looking to target...
Hi,
I'm using PWM on a nRF52832 (nRF52 DK) with SDK 17.0.2 . I have 3 PWM channels configured to LED2, LED3 and LED4. Below are my questions. I'm using PWM to dim the LED...
Hi there,
I'm starting a new project using an nRF52840 that interfaces with a Quectel BG95 modem with AT commands. Ultimately, I need to use MQTT to an Azure cloud environment...
We are measuring advertisment current consumption with CODED and it's averaging about ~400uA. Advertising on 1MBPs is right around where it should be ~30uA. Advertising interval...
Dear Nordic engineer.
I am using nrf9160.
I follow the instructions to download Fota using AWS upload file update.bin.
After the device has downloaded the file and receives...
WHY ARE SO MANY UN-NECESSARY LIBRARIES INCLUDED IN SIMPLE EXAMPLES?
I'm using nrf52 for a consumer device. Just loaded up the blinky example (under the peripheral folder...
Hello everyone,
I was trying to compile ble_app_uart code in segger embedded stdio but sample code not compile this sofware any configuration setting i need to change.....
Running nrf_drv_saadc_calibrate_offset() doesn't seem to work. I'm monitoring a 3v battery. Shown below is the debug output where the calibration is run after the event number...
