Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
There's a Bluetooth mesh sensor server, which realize, for example:
present ambient temperature property and
desired ambient temperature property.
A Bluetooth mesh...
Good morning,
I'm trying to port the HTS to the PCA0056 board towards chip nRF52833.
I followed the guideline and modified memory mapping as follows:
Section Placement...
Hi.
I'm currently trying to scan non-connectable advertisement for continuously.
So, I'm going to set the value of scan window and scan interval same.
For that purpose...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
Hi,
I am trying to setup the serial UART DFU process for a custom board. I am able to build and program a combined firmware hex file which includes - Softdevice S140 ...
Hi guys
I have a project that needs to use multiple 1.8V sensors and transmit data to the mobile phone through Bluetooth. If NRF52832 also uses 1.8V power supply, it can...
Hi Everybody,
I have obtained a free personal Segger Embedded Studio license to use on a nRF52 evaluation board and started to write and debug code.
When I port my code...
Hi,
I use the latest connect sdk 1.4.0 and modem firmware 1.2.2. If I load the default aws_iot code it does not subscribe to the topics set in "topics_list" in the code...
I am using SES Nordic Edition 4.52 and I am building a Zephyr project configured with nRF Connect SDK. After the initial build completes, every time I build without cleaning...
I have a device using the nRF51822 chip on which I was successfully using the BLE sniffer V3.0.0 PCA10028 firmware. The latest V3.1.0 PCA10028 firmware does not work but I...
I am trying to download version 8.31.1 of the nRF device firmware pack for keil from this link
developer.nordicsemi.com/.../NordicSemiconductor.nRF_DeviceFamilyPack.8.32...
Hi.
I'm trying to integrate the MPU9250 with nRF52832 using i2c (TWI) on my nRF52-DK
I have found various libraries but none of them are working on my hardware. All of...
After several record updates one by one I get FDS_ERR_NO_SPACE_IN_QUEUES. However after each record update I wait for FDS_EVT_UPDATE event. I was sure that waiting for this...
I have %XRFTEST working on the 9160 in every band listed in the datasheet other than Band 14 and 17. Is there a reason these bands are not supported with the test mode?
...
I'm looking into integrating the SoftDevice controller (not full SoftDevice) from nrfxlib into NuttX RTOS. NuttX would already provide the host layer so I would only need...
