Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi, i am working on a bluetooth application with the nRF52832. When i try to connect a Samsung Galaxy S8 (Android 8.0) via nRF Connect, i get a LMP TIMEOUT error after 40...
Launch, then select 'Launch Programmer, tool displays message "The app only supports nRF connect ^2.5.0 while your installed version is 3.0.0. It might not work as expected...
From what I could see the Asset_Tracker example works in LTE, not in NB-IoT. How can I test NB-IoT?
I would like to get some hint on what example to use and what to do to...
Hey all,
I'm a bit lost here... I developed a wireless sensor for a customer based on the nRF52840 and it works great. Now we're developing a small light weight gateway...
Hi everyone,
I'm trying to developp a MIDI USB class compliant device with the nrf52840 DK.
I'm beginner about USB developpement and I have only basics about MIDI class...
I am using SDK 15.3.0 working on nRF52832, on windows platform.
Our requirement is, we need to get the data from both nRF52832 and BLE Heart rate sensor at same time and...
I have developed a new board based around NRF91 module. Ten prototypes are produced and six of them work. Other four devices cannot connect to the LTE network. I am using...
Hi,
I'm using nrf_serial to configure and then read data from a GPS engine, but I am getting unrecoverable OVERRUN errors on start-up if the GPS device is sending data when...
Hello
the setup is a nrf52840, the sdk15.3, Softdevice s140, apps: open bootloader and blinky app
Is there a way that the DFU mode is always there, at the moment its only...
Hi,
We are in the HW verification stage of a product with an nRF52 series MCU. We were easily able to measure the 32MHz XTAL accuracy using the buffered output feature;...
Hello, Dear Support!
From the DevZone I downloaded ntf5-multilink-example-master. Here . Thanks for developers. The solution in SES was built and uploaded without any troubles...
I am using 'Segger Embedded Studio'. While changing the settings of a project in options, why we select Private Configurations (common)? I have seen this procedure in many...
Hi,I had a new project base on nRF52810. I watnted to created a timer, but the note mentioned " increase the value of the macro APP_TIMER_MAX_TIMERS by one ".I couldn't find...
Hi,
is nRF9160 SiP comes with eSIM? or do I need to insert external SIM in socket which is traditional method?
Do I need to external chip antenna? does that antenna...
Hi:
Because our project using much nRF pin resources, we have to use the defualt function NFC pins (P0.09 and P0.10).we want to set these two pins as uart function ,but...
