Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi,
Some time ago I ask a question about changing the publish address of a node in the mesh locally. I received the answer in the following threat and verified it:
https...
Hi All,
I used the app "ble_app_uart" and "ble_app_uart_c" on two custom boards mounting a n52840 QIAACO.
I know that in the app (nRF5_SDK_15.1.0_a8c0c4d\examples\ble_peripheral...
Dear Sir/Madam,
I want to measure the data speed between two BLE 4.2 based devices and two BLE 5.0 based devices.
Using nRF52 products for this purpose.
Kindly help...
I know that the nRF52832 is strictly a 3.3V device however, I was wondering whether any of the GPIO pins are 5V tolerant?
Is there any internal clamping diodes within the...
Hello,
I have noticed, that https://github.com/NordicSemiconductor/nrfx was updated with a nfct driver. I am trying to extended the nrfx port on micropython (see https:...
Hi,
I'm trying to setup the Peer Manager on a nRF51822 with installed the S130. I'm working with Eclipse where I installed the 12.3.0 SDK.
At compilation time I get the...
Hi, I have a two part question, I know the NRF51822 (and I believe all 4.0 BLE chipsets) are being sunset, when will this start taking place?
Since I'm currently using the...
HI,
i am using nrf51422 with sdk13.3.0 and soft device 130
i am receiving 69 byte of data through UART, i am compressing data in two packets. here after transmitting a...
I have an issue with BLE on Android when using low duty-cycle directed advertising and I'm asking here hoping some people have already seen that issue or something similar...
Hi,
I'm working on a custom bootloader based on the one included with SDK 15.
I have a blocking method (i.e. while loop) that runs at the end of the transmission of all...
Hi,
Some general Nordic BLE device questions:
How to add Characteristic?
How to send data to given c haracteristic?
We are using SoftDevice 132 with Segger IDE.
...
I am trying to free up some RAM on my nRF because I am getting Fatal error 0x4, NRF_ERROR_NO_MEM when I try to increase the size of a 2D array.
I do not understand how to...
Hi there,
I am considering the NRF52840 to build our new platform but I am struggling to find information about how the device Firmware is programmed.
Apart from SWD...
Hi,
I'm using sdk 15.2, with soft device s140 on nrf52840 dongle in peripheral mode. I'm using modiffied ble_app_proximity example. What I wan't to achieve is to set advertising...
