Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I have VSCode 1.63.0 (Universal) on macOS 12.0.1 with ncs v1.7.1 and a board with an nRF52840 MCU. I'm using the "hello_world" example. If I power cycle the board I can start...
Hi,
I'm trying to connect to hook-up a debugger in VSCode to my target but am unable to. The hardware is custom and JLink connects fine with nrfjprog to program and erase...
Hi,
I'm trying to ,create a development environment for Alexa gadget in nRF52832.
here is the thing which I'm using:
1. nRF connect for desktop version v3.9.1
2. Toolchain...
I had a Thingy91 that I think I bricked in trying to upgrade the firmware. I'm able to see the device in desktop programming, but it says erasing then gets to a 100% screen...
Dear, I am new to Nordic. I created a simple project for testing. There is a small fucntion to display "Hello World". After , Re-build Solution.. the memory used is as shown...
Dear community,
I am evaluating the nrf52 chip on the nrf52dk. I am using the peripheral_uart example, built for nrf52810. I have stumbled upon an error which I'm not sure...
In our BLE connections we often receive a BLE_GATTC_EVT_WRITE_RSP event with gatt_status 0x01F2.
Looking at the list of GATT_STATUS values, this must be an error in the...
Hi, based on my previous posts ( 2nd post , 1st post ) regarding the ble_app_uart_c multilink example I now face another issue.
When I run the multilink example on my nRF52840...
Hello,
Until now we compiled our company project using SEGGER Embedded Studio command line tool 'emBuild' that was called from a custom Makefile like this:
But we...
Hi all,
I want to self provision my node. I am using nrf52832 dev board, mesh SDK v 3.1.0, light switch client example. You may wonder why self provisioning, when there...
Hi, I am currently utilizing an app that supports multi link; however, I was only able to get 7 maximum stable connections. My goal for this multi-link is to connect a sensor...
Hi,
I am trying to run the DNS example provided in the Nordic Infocenter as part of the Thread Border Router setup, but it is not working. I am getting "Error 28: ResponseTimeout...
Hello,
I tried to implement the HX711 example from Vidar mentioned here ( https://devzone.nordicsemi.com/f/nordic-q-a/34112/best-approach-to-interface-hx711-with-nordic...
Dear, I am developing first project for self training using Nordic MCU. I want to interface few Buttons, Leds and LCD. I read the Datasheet nRF5340_PS_v1.0.pdf. In it in the...
We have selected ble_app_hrs_pca10059_s140 file in peripheral and ble_app_hrs_c_pca10040_s132 in central device, Now we can able to send heart rate value to central board...
