I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello.
I want to raise the SDK version, what should I do at that time? (Example: v16.0.0 → v17.0.2) Should I overwrite all the old SDK sources I'm using with the new SDK...
Hi, I'm using the PWR_MGMT SDK 17.0.2 demo code on my nRF52 DK.
Q1) After enabling parameters in the sdk_config.h, the nRF52 DK could enter the Power Off Mode if I press...
I am trying to conduct a device firmware update using nrfutil's dfu ble functionality. Here is the command:
However, running the above command results in the following...
Has anyone used SDCard interface with either 52840 or 5340 in anything other than SPI mode? I just noticed in the SDK 15.3 code we are using SDCard is in SPI mode. Seems max...
Hello,
I want to connect an external led to the nrf5340 pdk to perform the same function as the blinky example.
I connected this led to D0 (PIN P1.00), but I don't know...
Hi,
We are trying to send a mesh packets containing 72 bytes from client to server with reliable message transmission method (Using access_model_reliable_cancel() based...
nRF52840 with SoftDevice s140, rev 7.01. For this errata, the work around is to use READY instead. Is the SoftDevice doing this? I can't find any info. I did find a related...
We're using the nRF52840 along with SoftDevice s140 version 7.01 for a medical device. Reviewing the nRF52840 Errata sheet, Rev2, there is an errata "242 NVMC: NVMC operations...
Hi nordic community,
I'm using Open Thread Border Router build using Linux and an nrf52840 dk board, I want to show my sensor data in open thread border router web GUI,...
Hello,
I have changed the provided UDP sample to send some cellular data (RSRP, RSRQ) to our server within an fixed intervall. So I am using a few AT commands (at_cmd_write...
Hi, like the title says I am having trouble implementing the MQTT Publisher example found in the nRF5 SDK for Thread and Zigbee v4.1.0 . I'm using a Raspberry Pi 4 with the...
Have a medical device in production using nRF52840 with SoftDevice s140, 7.01. Is this Errata fixed or a workaround is implemented in this SoftDevice version or any version...
Hi Nordic Team:
1. I use this example " Thread MQTT-SN Example ".
after i compile the code than i do the step below
1.Build the example according to the instructions...
Hello,
What are all the supported cipher suites for the nrf9160? Per your documentation, it seems AES 128 is supported but not AES 256. But, based on some testing with slightly...
