Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello everyone,
I am going to run the serial DFU example. I follow the instruction on infocenter website and run the example by using my own keys and image and I got this...
Hello everyone! I'm creating BLE HID controller, where high packet rate is important. I expect about 100 packets per second. But when I try to launch hid mouse or hid keyboard...
Hi,
I am using NRF52832 based module. What is the maximum no of notifications we can send per sec. Is there any limit.
I am facing a issues on increasing the distance...
Hi Guys. I see that yesterday Nordic announced the nRF5340DK touting LE Audio. Is there a SOURCE and SINK example that even preliminarily demonstrates this capability on the...
plan to build a bluetooth to Nbiot edge gateway module and select nRF52832. Build the module to combine the nRF52832+BG96(Quectel)+multiple sensors include BME280,LIS3DH,LIS2MDL...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi,
I have a problem with nrf5340pdk not executing the firmware. I have to build a hello_world sample from ncs v1.4.99-dev1 and I flash the development kit with the west...
I'm considering rolling back to the sdk ver 14 to avoid the nrfx vs legacy api confusion.
I plan to use only the 52810 and 52832 SoCs.
Is there any disadvantage to using...
Hi @Vidar Berg
Hope you are doing well ! i need your help regarding the beacon coded phy . I read your post
https://devzone.nordicsemi.com/f/nordic-q-a/69595/problem-with...
Hello.
Trying to compile the AES CBC MAC example out of the box, we get the ferror below.
Your help would be appreciated.
Many thanks,
Andrew
Building ‘nrf_crypto_aes_cbc_mac_pca10040...
Hello,
Updating developer machines to OSX Big Sur resulted in nrfutil failing to execute. The install via pip works correctly, but when attempting to run the binary, the...
Hi All,
We have tested the DFU(nrf52840) from a central to the target device over the BLE. In which a central device attached to the PC(x86-64bit Linux) via a Serial USB...
Hi Folks,
I am facing an issue while trying to perform a system On suspend procedure with a wake up on HITOLOW event.
No event is triggered when button pressed.
However...
I wish to develop a bare metal application (without Zephyr) on the nRF5340.
For this purpose I am unable to find the documentation how to perform Inter Processor Communication...
