Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I tried to reduced my hex file's size while converting to zip but it doesn't get size under 256KB due to which I am getting an error: Data size exceeds the limit.
Below...
Hey,
I don't get my application run on the nrf52840-dk board. Only if I choose "Build and Debug" I can run my software. Shouldn't the application start after I connect to...
I would like to receive data on UART asynchronously and handle the RX event in the backend in an IRQ handler. The application is - a user will be shown a menu and asked to...
Hi Sir,
If we would like to supply the external device through VDD = 1.8V when VDDH = 2.5V.
What is power efficient in nRF52840 when VDD = 1.8V when VDDH = 2.5V?
...
Hi!
We have been experimenting with the nRF9160's GPS using both one of our own custom board and the Development Kit v 0.8.5 (with similar results).
We run the gps sample...
Hi,
I am receiving the same error this guy was: " https://devzone.nordicsemi.com/f/nordic-q-a/28724/sdk-for-mesh-v1-0-0-with-ses-invalid-ascii-encoded-byte-line-1 " and...
Is the Altium integrated libary used in the Altium files for the nRF9160 DK available anywhere? It is not included in the hardware file download on Nordic's website.
Looks...
The problem is shown in the picture below.
It is normal for 10 seconds after activating the timer.
As you can see in the picture, the value of the time stamp changes...
Our application uses and external nand flash to store the data samples. The collected data is then be transferred using USB. So we chose usbd_ble_uart example and wrote code...
Hey,
I am working on mesh with nrf52 DK. I want my device to work on battery for long time, I have enabled the MESH_FEATURE_LPN_ENABLED macro in nrf_mesh_config_core.h file...
I'm returning an error code on a rw_authorized characteristic using uint32_t sd_ble_gatts_rw_authorize_reply(uin16_t conn_handle, ble_gatts_rw_authorize_reply_params_t * auth_reply...
When using the PB-ADV bearer there is a ~10 second delay after the Link is closed and the mesh stack starts working again.
This is related to my previous report https:/...
I am trying to develop a SPI interface to a CANBUS controller for the nRF9160 for the zephyr platform.
The issue I am having at this point is is that I am unable to see...
