Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I was trying to measure the current used by the nRF52840 on the DK. But it seems like i have messed up.
The debugger LED does not light up
The nRF52840 SOC seems to...
hi team,
i have downloaded image transfer demo source code in github. installed it in sdk 13.0. the softdevice is 5.0.0-2. i am using nrf52840 pdk. the code is successfully...
Hi Al
I'm implementing multiple channel ADC with PPI
sampling multiple ADC channels with PPI, adc event triggered adc_event_handler as many times as channels (instead...
Hello everyone. I'm working to a project with nRF52840. I'm developing the code in SDK in SES ide. The task i want to perform is transfer data from the memory of nRF52840...
Hi,
I am using the S130 central pairing to just one peripherial at a time. Upon power up after hard/soft reset, the central connects to my peripherial just fine, transfer...
Hello,
We are using the Segger Embedded Studio and trying to flash the blinky code on our nRF52DK. We have seen many videos but are unable to make it work. The code gets...
Hi,
In my memory usage, I see 780KB free from 1MB of flash. That means I am already consuming 244KB of flash when my code size is only 77KB. Obviously, there are other registers...
I have been trying to flash my nrf51822 by waveshare using my nrf 51 DK. I have been making the following connection. I am currently using P20 as the needle adapter for P19...
Dear Nordic Team,
Thanks for supporting.
Now i am try to interface(TWI) MMA8453 with nRF52810. Already i am worked with nRF52832 its working good. If possible for interface...
I tried to add a BAS service to a project with an LBS service (ble_app_blinky), but I cannot complete the services_init() procedure for both services.
Is it possible to...
Hello,
I would like to kwno if it is possible to get information about the hardware in my main application. NRF_DFU_HW_VERSION is stored in the DFU and is used to verify...
Hi all
I want to stream data from various nRF52 objects to a single Android smarphone.
I have no problem in evaluating the throughput of each nRF52 device to the client...
Hi,
I want to set up a demo bike speed and cadence transmitter. I am using \ant\ant_plus\ant_bsc\bsc_tx source code. However, I have plans to use BLE at the same time...
Hi,
Are softdevice's api calls thread safe (specifically speaking sd_ble_gatts_hvx ()) -
i.e. Will a concurrent call to sd_ble_gatts_hvx () from several threads corrupt...
