Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I'm had develloped some software and tested it on the nRF51-DK.
After that I made my own PCB design where only the nRF51422 is replaced by a nRF51822.
When I flash both...
I have a legacy RN42 BT2.1+EDR running in a system as the network master that I need to connect/pair with a nRF51422 BLE dev kit, and am having problems.
The BLE just doesn...
HI All,
I tried to migrate from nRF51_SDK_10.0.0_dc26b5e to nRF5_SDK_11.0.0-2.alpha_bc3f6a0
my migrated ble_stack_init:
static void ble_stack_init(void)
{
uint32_t...
I will try to use the s110 8.0.0
But I can not find the sdk installer from the website.
Three months ago, when I visited the website, there is a SDK 6.xx.xx Installer...
Hi.
I'm currently receiving advertisement packet from beacon scanner app. (nrf51822)
(ble_peripheral/experimental_ble_app_multiactivity_beacon/hrs_scanner)
I tried...
Hi, I am here in the use of Flash memory data when there is a strange question to consult.
Due to my side of the application, you need to enter each case sd_power_system_off...
Using nRF51 SDK 10.0, it seems like many debug prints are incorrect, triggering a GCC format warning resulting in a compilation error with -Wall turned on.
A workaround is...
I'm using a custom designed PCB around the NRF51822 that broadcasts accelerometer readouts on a characteristic.
The application is based on s110 uart example and has been...
i wantto compile ''ble_app_hrs_c'' from sdk
but it always show up likes
" C:\Program Files\CodeBlocks\MinGW\include\SDK 7.2\examples\ble_central\ble_app_hrs_c\main.c|19...
keil use pclint, it will give lots of info message or warning message.what 's the best configuration to filter these info message ?? just display the error or warning message...
Hi
I'm trying to test UART over BLE using A custom board with a nRF51822,S110_NRF51822_7.1.0
SDK 6_1_1, Code is Github "NordicSemiconductor/nRF51-ble-app-uart-static-passkey...
I'm a beginner, the question might be simple but its really important for me.
What would the current flowing through Empty nrf51822 when it is completely erased or empty...
In bootloader of sdk9
I find
ble_gap_addr_t addr;
err_code = sd_ble_gap_address_get(&addr);
APP_ERROR_CHECK(err_code);
// Increase the BLE address by one when advertising...
